This is zebra.info, produced by makeinfo version 4.2 from zebra.texi.

INFO-DIR-SECTION Routing Software:
START-INFO-DIR-ENTRY
* Zebra: (zebra).		The GNU Zebra routing software
END-INFO-DIR-ENTRY

   This file documents the GNU Zebra software which manages common
TCP/IP routing protocols.

   This is Edition 0.1, last updated 28 June 2002 of `The GNU Zebra
Manual', for Zebra Version 0.93.

   Copyright (C) 1999, 2000, 2001, 2002 Kunihiro Ishiguro

   Permission is granted to make and distribute verbatim copies of this
manual provided the copyright notice and this permission notice are
preserved on all copies.

   Permission is granted to copy and distribute modified versions of
this manual under the conditions for verbatim copying, provided that the
entire resulting derived work is distributed under the terms of a
permission notice identical to this one.

   Permission is granted to copy and distribute translations of this
manual into another language, under the above conditions for modified
versions, except that this permission notice may be stated in a
translation approved by Kunihiro Ishiguro.


File: zebra.info,  Node: Top,  Next: Overview,  Prev: (dir),  Up: (dir)

Zebra
*****

   Zebra is a advanced routing software package that provides TCP/IP
based routing protocols.  This is the Zebra Manual for zebra-0.93.

* Menu:

* Overview::
* Installation::
* Basic commands::
* Zebra::
* RIP::
* RIPng::
* OSPFv2::
* OSPFv3::
* BGP::
* VTY shell::
* Filtering::
* Route Map::
* IPv6 Support::
* Kernel Interface::
* SNMP Support::
* Zebra Protocol::
* Packet Binary Dump Format::
* Command Index::
* VTY Key Index::


File: zebra.info,  Node: Overview,  Next: Installation,  Prev: Top,  Up: Top

Overview
********

   Zebra is a routing software package that provides TCP/IP based
routing services with routing protocols support such as RIPv1, RIPv2,
RIPng, OSPFv2, OSPFv3, BGP-4, and BGP-4+ (*note Supported RFC::).
Zebra also supports special BGP Route Reflector and Route Server
behavior.  In addition to traditional IPv4 routing protocols, Zebra
also supports IPv6 routing protocols.  With SNMP daemon which supports
SMUX protocol, Zebra provides routing protocol MIBs (*note SNMP
Support::).

   Zebra uses an advanced software architecture to provide you with a
high quality, multi server routing engine.  Zebra has an interactive
user interface for each routing protocol and supports common client
commands.  Due to this design, you can add new protocol daemons to Zebra
easily.  You can use Zebra library as your program's client user
interface.

   Zebra is an official GNU software and distributed under the GNU
General Public License.

* Menu:

* About Zebra::                 Basic information about Zebra
* System Architecture::         The Zebra system architecture
* Supported Platforms::         Supported platforms and future plans
* Supported RFC::               Supported RFCs
* How to get Zebra::
* Mailing List::                Mailing list information
* Bug Reports::                 Mail address for bug data


File: zebra.info,  Node: About Zebra,  Next: System Architecture,  Prev: Overview,  Up: Overview

About Zebra
===========

   Today, TCP/IP networks are covering all of the world.  The Internet
has been deployed in many countries, companies, and to the home.  When
you connect to the Internet your packet will pass many routers which
have TCP/IP routing functionality.

   A system with Zebra installed acts as a dedicated router.  With
Zebra, your machine exchanges routing information with other routers
using routing protocols.  Zebra uses this information to update the
kernel routing table so that the right data goes to the right place.
You can dynamically change the configuration and you may view routing
table information from the Zebra terminal interface.

   Adding to routing protocol support, Zebra can setup interface's
flags, interface's address, static routes and so on.  If you have a
small network, or a stub network, or xDSL connection, configuring the
Zebra routing software is very easy.  The only thing you have to do is
to set up the interfaces and put a few commands about static routes
and/or default routes.  If the network is rather large, or if the
network structure changes frequently, you will want to take advantage
of Zebra's dynamic routing protocol support for protocols such as RIP,
OSPF or BGP.  Zebra is with you.

   Traditionally, UNIX based router configuration is done by `ifconfig'
and `route' commands.  Status of routing table is displayed by
`netstat' utility.  Almost of these commands work only if the user has
root privileges.  Zebra has a different system administration method.
There are two user modes in Zebra.  One is normal mode, the other is
enable mode.  Normal mode user can only view system status, enable mode
user can change system configuration.  This UNIX account independent
feature will be great help to the router administrator.

   Currently, Zebra supports common unicast routing protocols.
Multicast routing protocols such as BGMP, PIM-SM, PIM-DM will be
supported in Zebra 2.0.  MPLS support is going on.  In the future,
TCP/IP filtering control, QoS control, diffserv configuration will be
added to Zebra.  Zebra project's final goal is making a productive,
quality free TCP/IP routing software.


File: zebra.info,  Node: System Architecture,  Next: Supported Platforms,  Prev: About Zebra,  Up: Overview

System Architecture
===================

   Traditional routing software is made as a one process program which
provides all of the routing protocol functionalities.  Zebra takes a
different approach.  It is made from a collection of several daemons
that work together to build the routing table.  There may be several
protocol-specific routing daemons and zebra the kernel routing manager.

   The `ripd' daemon handles the RIP protocol, while `ospfd' is a
daemon which supports OSPF version 2.  `bgpd' supports the BGP-4
protocol.  For changing the kernel routing table and for redistribution
of routes between different routing protocols, there is a kernel
routing table manager `zebra' daemon.  It is easy to add a new routing
protocol daemons to the entire routing system without affecting any
other software.  You need to run only the protocol daemon associated
with routing protocols in use.  Thus, user may run a specific daemon
and send routing reports to a central routing console.

   There is no need for these daemons to be running on the same machine.
You can even run several same protocol daemons on the same machine.
This architecture creates new possibilities for the routing system.

     +----+  +----+  +-----+  +-----+
     |bgpd|  |ripd|  |ospfd|  |zebra|
     +----+  +----+  +-----+  +-----+
                                 |
     +---------------------------|--+
     |                           v  |
     |  UNIX Kernel  routing table  |
     |                              |
     +------------------------------+
     
         Zebra System Architecture

   Multi-process architecture brings extensibility, modularity and
maintainability.  At the same time it also brings many configuration
files and terminal interfaces.  Each daemon has it's own configuration
file and terminal interface.  When you configure a static route, it must
be done in `zebra' configuration file.  When you configure BGP network
it must be done in `bgpd' configuration file.  This can be a very
annoying thing.  To resolve the problem, Zebra provides integrated user
interface shell called `vtysh'.  `vtysh' connects to each daemon with
UNIX domain socket and then works as a proxy for user input.

   Zebra was planned to use multi-threaded mechanism when it runs with a
kernel that supports multi-threads.  But at the moment, the thread
library which comes with GNU/Linux or FreeBSD has some problems with
running reliable services such as routing software, so we don't use
threads at all.  Instead we use the `select(2)' system call for
multiplexing the events.

   When `zebra' runs under a GNU Hurd kernel it will act as a kernel
routing table itself.  Under GNU Hurd, all TCP/IP services are provided
by user processes called `pfinet'.  Zebra will provide all the routing
selection mechanisms for the process.  This feature will be implemented
when GNU Hurd becomes stable.


File: zebra.info,  Node: Supported Platforms,  Next: Supported RFC,  Prev: System Architecture,  Up: Overview

Supported Platforms
===================

   Currently Zebra supports GNU/Linux, BSD and Solaris.  Below is a list
of OS versions on which Zebra runs.  Porting Zebra to other platforms is
not so too difficult.  Platform dependent codes exist only in `zebra'
daemon.  Protocol daemons are platform independent.  Please let us know
when you find out Zebra runs on a platform which is not listed below.


   * GNU/Linux 2.0.37

   * GNU/Linux 2.2.x

   * GNU/Linux 2.3.x

   * FreeBSD 2.2.8

   * FreeBSD 3.x

   * FreeBSD 4.x

   * NetBSD 1.4

   * OpenBSD 2.5

   * Solaris 2.6

   * Solaris 7


   Some IPv6 stacks are in development.  Zebra supports following IPv6
stacks.  For BSD, we recommend KAME IPv6 stack.  Solaris IPv6 stack is
not yet supported.

   * Linux IPv6 stack for GNU/Linux 2.2.x and higher.

   * KAME IPv6 stack for BSD.

   * INRIA IPv6 stack for BSD.


File: zebra.info,  Node: Supported RFC,  Next: How to get Zebra,  Prev: Supported Platforms,  Up: Overview

Supported RFC
=============

   Below is the list of currently supported RFC's.

RFC1058
     `Routing Information Protocol. C.L. Hedrick. Jun-01-1988.'

RF2082
     `RIP-2 MD5 Authentication. F. Baker, R. Atkinson. January 1997.'

RFC2453
     `RIP Version 2. G. Malkin. November 1998.'

RFC2080
     `RIPng for IPv6. G. Malkin, R. Minnear. January 1997.'

RFC2328
     `OSPF Version 2. J. Moy. April 1998.'

RFC2740
     `OSPF for IPv6. R. Coltun, D. Ferguson, J. Moy. December 1999.'

RFC1771
     `A Border Gateway Protocol 4 (BGP-4). Y. Rekhter & T. Li. March
     1995.'

RFC1965
     `Autonomous System Confederations for BGP. P. Traina. June 1996.'

RFC1997
     `BGP Communities Attribute. R. Chandra, P. Traina & T. Li. August
     1996.'

RFC2545
     `Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain
     Routing. P. Marques, F. Dupont. March 1999.'

RFC2796
     `BGP Route Reflection An alternative to full mesh IBGP. T. Bates &
     R. Chandrasekeran. June 1996.'

RFC2858
     `Multiprotocol Extensions for BGP-4. T. Bates, Y. Rekhter, R.
     Chandra, D. Katz. June 2000.'

RFC2842
     `Capabilities Advertisement with BGP-4. R. Chandra, J. Scudder.
     May 2000.'

   When SNMP support is enabled, below RFC is also supported.

RFC1227
     `SNMP MUX protocol and MIB. M.T. Rose. May-01-1991.'

RFC1657
     `Definitions of Managed Objects for the Fourth Version of the
     Border Gateway Protocol (BGP-4) using SMIv2. S. Willis, J. Burruss,
     J. Chu, Editor. July 1994.'

RFC1724
     `RIP Version 2 MIB Extension. G. Malkin & F. Baker. November 1994.'

RFC1850
     `OSPF Version 2 Management Information Base. F. Baker, R. Coltun.
     November 1995.'


File: zebra.info,  Node: How to get Zebra,  Next: Mailing List,  Prev: Supported RFC,  Up: Overview

How to get Zebra
================

   Zebra is still beta software and there is no officially released
version.  So currently Zebra is distributed from Zebra beta ftp site
located at:

   <ftp://ftp.zebra.org/pub/zebra>

   Once Zebra is released you can get it from GNU FTP site and its
mirror sites.  We are planning Zebra-1.0 as the first released version.

   Zebra's official web page is located at:

   <http://www.gnu.org/software/zebra/zebra.html>.

   There is a Zebra beta tester web page at:

   <http://www.zebra.org/>.

   You can get the latest beta software information from this page.


File: zebra.info,  Node: Mailing List,  Next: Bug Reports,  Prev: How to get Zebra,  Up: Overview

Mailing List
============

   There is a mailing list for discussions about Zebra.  If you have any
comments or suggestions to Zebra, please send mail to
<zebra@zebra.org>.  New snapshot announcements, improvement notes, and
patches are sent to the list.

   To subscribe to the Zebra mailing list <zebra@zebra.org>, please
send a mail to <majordomo@zebra.org> with a message body that includes
only:

     subscribe zebra

   To unsubscribe from the list, please send a mail to
<majordomo@zebra.org> with a message body that includes only:

     unsubscribe zebra


File: zebra.info,  Node: Bug Reports,  Prev: Mailing List,  Up: Overview

Bug Reports
===========

   If you think you have found a bug, please send a bug report to
<bug-zebra@gnu.org>.  When you send a bug report, please be careful
about the points below.

   * Please note what kind of OS you are using.  If you use the IPv6
     stack please note that as well.

   * Please show us the results of `netstat -rn' and `ifconfig -a'.
     Information from zebra's VTY command `show ip route' will also be
     helpful.

   * Please send your configuration file with the report.  If you
     specify arguments to the configure script please note that too.

   Bug reports are very important for us to improve the quality of
Zebra.  Zebra is still in the development stage, but please don't
hesitate to send a bug report to <bug-zebra@gnu.org>.


File: zebra.info,  Node: Installation,  Next: Basic commands,  Prev: Overview,  Up: Top

Installation
************

   There are three steps for installing the software: configuration,
compilation, and installation.

* Menu:

* Configure the Software::
* Build the Software::
* Install the Software::

   The easiest way to get Zebra running is to issue the following
commands:

     % configure
     % make
     % make install


File: zebra.info,  Node: Configure the Software,  Next: Build the Software,  Prev: Installation,  Up: Installation

Configure the Software
======================

   Zebra has an excellent configure script which automatically detects
most host configurations.  There are several additional configure
options you can use to turn off IPv6 support, to disable the
compilation of specific daemons, and to enable SNMP support.

`--enable-guile'
     Turn on compilation of the zebra-guile interpreter.  You will need
     the guile library to make this.  zebra-guile implementation is not
     yet finished.  So this option is only useful for zebra-guile
     developers.

`--disable-ipv6'
     Turn off IPv6 related features and daemons.  Zebra configure script
     automatically detects IPv6 stack.  But sometimes you might want to
     disable IPv6 support of Zebra.

`--disable-zebra'
     Do not build zebra daemon.

`--disable-ripd'
     Do not build ripd.

`--disable-ripngd'
     Do not build ripngd.

`--disable-ospfd'
     Do not build ospfd.

`--disable-ospf6d'
     Do not build ospf6d.

`--disable-bgpd'
     Do not build bgpd.

`--disable-bgp-announce'
     Make `bgpd' which does not make bgp announcements at all.  This
     feature is good for using `bgpd' as a BGP announcement listener.

`--enable-netlink'
     Force to enable GNU/Linux netlink interface.  Zebra configure
     script detects netlink interface by checking a header file.  When
     the header file does not match to the current running kernel,
     configure script will not turn on netlink support.

`--enable-snmp'
     Enable SNMP support.  By default, SNMP support is disabled.

   You may specify any combination of the above options to the configure
script.  By default, the executables are placed in `/usr/local/sbin'
and the configuration files in `/usr/local/etc'. The `/usr/local/'
installation prefix and other directories may be changed using the
following options to the configuration script.

`--prefix=PREFIX'
     Install architecture-independent files in PREFIX [/usr/local].

`--sysconfdir=DIR'
     Read-only sample configuration file in DIR [PREFIX/etc].

     % ./configure --disable-ipv6

   This command will configure zebra and the routing daemons.

   There are several options available only to GNU/Linux systems: (1).

   ---------- Footnotes ----------

   (1) GNU/Linux has very flexible kernel configuration features.  If
you use GNU/Linux, make sure that the current kernel configuration is
what you want.  Zebra will run with any kernel configuration but some
recommendations do exist.

CONFIG_NETLINK
     Kernel/User netlink socket.  This is a brand new feature which
     enables an advanced interface between the Linux kernel and Zebra
     (*note Kernel Interface::).

CONFIG_RTNETLINK
     Routing messages.  This makes it possible to receive netlink
     routing messages.  If you specify this option, `zebra' can detect
     routing information updates directly from the kernel (*note Kernel
     Interface::).

CONFIG_IP_MULTICAST
     IP: multicasting.  This option should be specified when you use
     `ripd' or `ospfd' because these protocols use multicast.

   IPv6 support has been added in GNU/Linux kernel version 2.2.  If you
try to use the Zebra IPv6 feature on a GNU/Linux kernel, please make
sure the following libraries have been installed.  Please note that
these libraries will not be needed when you uses GNU C library 2.1 or
upper.

`inet6-apps'
     The `inet6-apps' package includes basic IPv6 related libraries such
     as `inet_ntop' and `inet_pton'.  Some basic IPv6 programs such as
     `ping', `ftp', and `inetd' are also included. The `inet-apps' can
     be found at <ftp://ftp.inner.net/pub/ipv6/>.

`net-tools'
     The `net-tools' package provides an IPv6 enabled interface and
     routing utility.  It contains `ifconfig', `route', `netstat', and
     other tools.  `net-tools' may be found at
     <http://www.tazenda.demon.co.uk/phil/net-tools/>.


File: zebra.info,  Node: Build the Software,  Next: Install the Software,  Prev: Configure the Software,  Up: Installation

Build the Software
==================

   After configuring the software, you will need to compile it for your
system. Simply issue the command `make' in the root of the source
directory and the software will be compiled. If you have *any* problems
at this stage, be certain to send a bug report *Note Bug Reports::.

     % ./configure
     .
     .
     .
     ./configure output
     .
     .
     .
     % make


File: zebra.info,  Node: Install the Software,  Prev: Build the Software,  Up: Installation

Install the Software
====================

   Installing the software to your system consists of copying the
compiled programs and supporting files to a standard location. After the
installation process has completed, these files have been copied from
your work directory to `/usr/local/bin', and `/usr/local/etc'.

   To install the Zebra suite, issue the following command at your shell
prompt: `make install'.

     %
     % make install
     %

   Zebra daemons have their own terminal interface or VTY.  After
installation, you have to setup each beast's port number to connect to
them.  Please add the following entries to `/etc/services'.

     zebrasrv      2600/tcp		  # zebra service
     zebra         2601/tcp		  # zebra vty
     ripd          2602/tcp		  # RIPd vty
     ripngd        2603/tcp		  # RIPngd vty
     ospfd         2604/tcp		  # OSPFd vty
     bgpd          2605/tcp		  # BGPd vty
     ospf6d        2606/tcp		  # OSPF6d vty

   If you use a FreeBSD newer than 2.2.8, the above entries are already
added to `/etc/services' so there is no need to add it. If you specify
a port number when starting the daemon, these entries may not be needed.

   You may need to make changes to the config files in
`/usr/local/etc/*.conf'. *Note Config Commands::.


File: zebra.info,  Node: Basic commands,  Next: Zebra,  Prev: Installation,  Up: Top

Basic commands
**************

   There are five routing daemons in use, and there is one manager
daemon.  These daemons may be located on separate machines from the
manager daemon.  Each of these daemons will listen on a particular port
for incoming VTY connections.  The routing daemons are:

   * `ripd', `ripngd', `ospfd', `ospf6d', `bgpd'

   * `zebra'

   The following sections discuss commands common to all the routing
daemons.

* Menu:

* Config Commands::             Commands used in config files
* Common Invocation Options::   Starting the daemons
* Virtual Terminal Interfaces::  Interacting with the daemons


File: zebra.info,  Node: Config Commands,  Next: Common Invocation Options,  Prev: Basic commands,  Up: Basic commands

Config Commands
===============

* Menu:

* Basic Config Commands::       Some of the generic config commands
* Sample Config File::          An example config file

   In a config file, you can write the debugging options, a vty's
password, routing daemon configurations, a log file name, and so forth.
This information forms the initial command set for a routing beast as
it is starting.

   Config files are generally found in:

     `/usr/local/etc/*.conf'

   Each of the daemons has its own config file.  For example, zebra's
default config file name is:

     `/usr/local/etc/zebra.conf'

   The daemon name plus `.conf' is the default config file name. You
can specify a config file using the `-f' or `--config-file' options
when starting the daemon.


File: zebra.info,  Node: Basic Config Commands,  Next: Sample Config File,  Prev: Config Commands,  Up: Config Commands

Basic Config Commands
---------------------

 - Command: hostname HOSTNAME
     Set hostname of the router.

 - Command: password PASSWORD
     Set password for vty interface.  If there is no password, a vty
     won't accept connections.

 - Command: enable password PASSWORD
     Set enable password.

 - Command: log stdout
 - Command: no log stdout
     Set logging output to stdout.

 - Command: log file FILENAME
     If you want to log into a file please specify `filename' as
     follows.
          log file /usr/local/etc/bgpd.log

 - Command: log syslog
 - Command: no log syslog
     Set logging output to syslog.

 - Command: write terminal
     Displays the current configuration to the vty interface.

 - Command: write file
     Write current configuration to configuration file.

 - Command: configure terminal
     Change to configuration mode.  This command is the first step to
     configuration.

 - Command: terminal length <0-512>
     Set terminal display length to <0-512>.  If length is 0, no
     display control is performed.

 - Command: who

 - Command: list
     List commands.

 - Command: service password-encryption
     Encrypt password.

 - Command: service advanced-vty
     Enable advanced mode VTY.

 - Command: service terminal-length <0-512>
     Set system wide line configuration.  This configuration command
     applies to all VTY interfaces.

 - Command: show version
     Show the current version of the Zebra and its build host
     information.

 - Command: line vty
     Enter vty configuration mode.

 - Command: banner motd default
     Set default motd string.

 - Command: no banner motd
     No motd banner string will be printed.

 - Line Command: exec-timeout MINUTE
 - Line Command: exec-timeout MINUTE SECOND
     Set VTY connection timeout value.  When only one argument is
     specified it is used for timeout value in minutes.  Optional
     second argument is used for timeout value in seconds. Default
     timeout value is 10 minutes.  When timeout value is zero, it means
     no timeout.

 - Line Command: no exec-timeout
     Do not perform timeout at all.  This command is as same as
     `exec-timeout 0 0'.

 - Line Command: access-class ACCESS-LIST
     Restrict vty connections with an access list.


File: zebra.info,  Node: Sample Config File,  Prev: Basic Config Commands,  Up: Config Commands

Sample Config File
------------------

   Below is a sample configuration file for the zebra daemon.

     !
     ! Zebra configuration file
     !
     hostname Router
     password zebra
     enable password zebra
     !
     log stdout
     !
     !

   '!' and '#' are comment characters.  If the first character of the
word is one of the comment characters then from the rest of the line
forward will be ignored as a comment.

     password zebra!password

   If a comment character is not the first character of the word, it's a
normal character. So in the above example '!' will not be regarded as a
comment and the password is set to 'zebra!password'.


File: zebra.info,  Node: Common Invocation Options,  Next: Virtual Terminal Interfaces,  Prev: Config Commands,  Up: Basic commands

Common Invocation Options
=========================

   These options apply to all Zebra daemons.

`-d'
`--daemon'
     Runs in daemon mode.

`-f FILE'
`--config_file=FILE'
     Set configuration file name.

`-h'
`--help'
     Display this help and exit.

`-i FILE'
`--pid_file=FILE'
     Upon startup the process identifier of the daemon is written to a
     file, typically in `/var/run'.  This file can be used by the init
     system to implement commands such as `.../init.d/zebra status',
     `.../init.d/zebra restart' or `.../init.d/zebra stop'.

     The file name is an run-time option rather than a configure-time
     option so that multiple routing daemons can be run simultaneously.
     This is useful when using Zebra to implement a routing looking
     glass.  One machine can be used to collect differing routing views
     from differing points in the network.

`-P PORT'
`--vty_port=PORT'
     Set the VTY port number.

`-v'
`--version'
     Print program version.


File: zebra.info,  Node: Virtual Terminal Interfaces,  Prev: Common Invocation Options,  Up: Basic commands

Virtual Terminal Interfaces
===========================

   VTY - Virtual Terminal [aka TeletYpe] Interface is a command line
interface (CLI) for user interaction with the routing daemon.

* Menu:

* VTY Overview::                Basics about VTYs
* VTY Modes::                   View, Enable, and Other VTY modes
* VTY CLI Commands::            Commands for movement, edition, and management


File: zebra.info,  Node: VTY Overview,  Next: VTY Modes,  Prev: Virtual Terminal Interfaces,  Up: Virtual Terminal Interfaces

VTY Overview
------------

   VTY stands for Virtual TeletYpe interface.  It means you can connect
to the daemon via the telnet protocol.

   To enable a VTY interface, you have to setup a VTY password.  If
there is no VTY password, one cannot connect to the VTY interface at
all.

     % telnet localhost 2601
     Trying 127.0.0.1...
     Connected to localhost.
     Escape character is '^]'.
     
     Hello, this is zebra (version 0.93)
     Copyright 1997-2000 Kunihiro Ishiguro
     
     
     User Access Verification
     
     Password: XXXXX
     Router> ?
       enable            Turn on privileged commands
       exit              Exit current mode and down to previous mode
       help              Description of the interactive help system
       list              Print command list
       show              Show running system information
       who               Display who is on a vty
     Router> enable
     Password: XXXXX
     Router# configure terminal
     Router(config)# interface eth0
     Router(config-if)# ip address 10.0.0.1/8
     Router(config-if)# ^Z
     Router#

   '?' is very useful for looking up commands.


File: zebra.info,  Node: VTY Modes,  Next: VTY CLI Commands,  Prev: VTY Overview,  Up: Virtual Terminal Interfaces

VTY Modes
---------

   There are three basic VTY modes:

* Menu:

* VTY View Mode::               Mode for read-only interaction
* VTY Enable Mode::             Mode for read-write interaction
* VTY Other Modes::             Special modes (tftp, etc)

   There are commands that may be restricted to specific VTY modes.


File: zebra.info,  Node: VTY View Mode,  Next: VTY Enable Mode,  Prev: VTY Modes,  Up: VTY Modes

VTY View Mode
.............

   This mode is for read-only access to the CLI. One may exit the mode
by leaving the system, or by entering `enable' mode.


File: zebra.info,  Node: VTY Enable Mode,  Next: VTY Other Modes,  Prev: VTY View Mode,  Up: VTY Modes

VTY Enable Mode
...............

   This mode is for read-write access to the CLI. One may exit the mode
by leaving the system, or by escaping to view mode.


File: zebra.info,  Node: VTY Other Modes,  Prev: VTY Enable Mode,  Up: VTY Modes

VTY Other Modes
...............

   This page is for describing other modes.


File: zebra.info,  Node: VTY CLI Commands,  Prev: VTY Modes,  Up: Virtual Terminal Interfaces

VTY CLI Commands
----------------

   Commands that you may use at the command-line are described in the
following three subsubsections.

* Menu:

* CLI Movement Commands::       Commands for moving the cursor about
* CLI Editing Commands::        Commands for changing text
* CLI Advanced Commands::       Other commands, session management and so on


File: zebra.info,  Node: CLI Movement Commands,  Next: CLI Editing Commands,  Prev: VTY CLI Commands,  Up: VTY CLI Commands

CLI Movement Commands
.....................

   These commands are used for moving the CLI cursor. The <C> character
means press the Control Key.

`C-f'
`<RIGHT>'
     Move forward one character.

`C-b'
`<LEFT>'
     Move backward one character.

`M-f'
     Move forward one word.

`M-b'
     Move backward one word.

`C-a'
     Move to the beginning of the line.

`C-e'
     Move to the end of the line.


File: zebra.info,  Node: CLI Editing Commands,  Next: CLI Advanced Commands,  Prev: CLI Movement Commands,  Up: VTY CLI Commands

CLI Editing Commands
....................

   These commands are used for editing text on a line. The <C>
character means press the Control Key.

`C-h'
`<DEL>'
     Delete the character before point.

`C-d'
     Delete the character after point.

`M-d'
     Forward kill word.

`C-w'
     Backward kill word.

`C-k'
     Kill to the end of the line.

`C-u'
     Kill line from the beginning, erasing input.

`C-t'
     Transpose character.


File: zebra.info,  Node: CLI Advanced Commands,  Prev: CLI Editing Commands,  Up: VTY CLI Commands

CLI Advanced Commands
.....................

   There are several additional CLI commands for command line
completions, insta-help, and VTY session management.

`C-c'
     Interrupt current input and moves to the next line.

`C-z'
     End current configuration session and move to top node.

`C-n'
`<DOWN>'
     Move down to next line in the history buffer.

`C-p'
`<UP>'
     Move up to previous line in the history buffer.

`TAB'
     Use command line completion by typing <TAB>.

`'
     You can use command line help by typing `help' at the beginning of
     the line.  Typing `?' at any point in the line will show possible
     completions.


File: zebra.info,  Node: Zebra,  Next: RIP,  Prev: Basic commands,  Up: Top

Zebra
*****

   `zebra' is an IP routing manager.  It provides kernel routing table
updates, interface lookups, and redistribution of routes between
different routing protocols.

* Menu:

* Invoking zebra::              Running the program
* Interface Commands::          Commands for zebra interfaces
* Static Route Commands::       Commands for adding static routes
* zebra Terminal Mode Commands::  Commands for zebra's VTY


File: zebra.info,  Node: Invoking zebra,  Next: Interface Commands,  Prev: Zebra,  Up: Zebra

Invoking zebra
==============

   Besides the common invocation options (*note Common Invocation
Options::), the `zebra' specific invocation options are listed below.

`-b'
`--batch'
     Runs in batch mode.  `zebra' parses configuration file and
     terminates immediately.

`-k'
`--keep_kernel'
     When zebra starts up, don't delete old self inserted routes.

`-l'
`--log_mode'
     Set verbose logging on.

`-r'
`--retain'
     When program terminates, retain routes added by zebra.


File: zebra.info,  Node: Interface Commands,  Next: Static Route Commands,  Prev: Invoking zebra,  Up: Zebra

Interface Commands
==================

 - Command: interface IFNAME

 - Interface Command: shutdown
 - Interface Command: no shutdown
     Up or down the current interface.

 - Interface Command: ip address ADDRESS
     Set ip address for the interface.

 - Interface Command: description DESCRIPTION ...
     Set description for the interface.

 - Interface Command: multicast
 - Interface Command: no multicast
     Enable or disables multicast flag for the interface.

 - Interface Command: bandwidth <1-10000000>
 - Interface Command: no bandwidth <1-10000000>
     Set bandwidth value to the interface.  This is for calculating OSPF
     cost.  This command does not affect the actual device
     configuration.


File: zebra.info,  Node: Static Route Commands,  Next: zebra Terminal Mode Commands,  Prev: Interface Commands,  Up: Zebra

Static Route Commands
=====================

   Static routing is a very fundamental feature of routing technology.
It defines static prefix and gateway.

 - Command: ip route NETWORK GATEWAY
     NETWORK is destination prefix with format of A.B.C.D/M.  GATEWAY
     is gateway for the prefix.  When GATEWAY is A.B.C.D format.  It is
     taken as a IPv4 address gateway.  Otherwise it is treated as an
     interface name.

          ip route 10.0.0.0/8 10.0.0.2
          ip route 10.0.0.0/8 ppp0

     First example defines 10.0.0.0/8 static route with gateway
     10.0.0.2.  Second one defines the same prefix but with gateway to
     interface ppp0.

 - Command: ip route NETWORK NETMASK GATEWAY
     This is alternate version of above command.  When NETWORK is
     A.B.C.D format, user must define NETMASK value with A.B.C.D
     format.  GATEWAY is same option as above command

          ip route 10.0.0.0 255.255.255.0 10.0.0.2
          ip route 10.0.0.0 255.255.255.0 ppp0

     This is a same setting using this statement.

 - Command: ip route NETWORK GATEWAY DISTANCE

   Multiple nexthop static route

     ip route 10.0.0.1/32 10.0.0.2
     ip route 10.0.0.1/32 10.0.0.3
     ip route 10.0.0.1/32 eth0

   If there is no route to 10.0.0.2 and 10.0.0.3, and interface eth0 is
reachable, then the last route is installed into the kernel.

     zebra> show ip route
     S>  10.0.0.1/32 [1/0] via 10.0.0.2 inactive
                           via 10.0.0.3 inactive
       *                   is directly connected, eth0

   Floating static route

 - Command: ipv6 route NETWORK GATEWAY

 - Command: ipv6 route NETWORK GATEWAY DISTANCE

 - Command: table TABLENO
     Select the primary kernel routing table to be used.  This only
     works for kernels supporting multiple routing tables (like
     GNU/Linux 2.2.x and later).  After setting TABLENO with this
     command, static routes defined after this are added to the
     specified table.


File: zebra.info,  Node: zebra Terminal Mode Commands,  Prev: Static Route Commands,  Up: Zebra

zebra Terminal Mode Commands
============================

 - Command: show ip route
     Display current routes which zebra holds in its database.

          Router# show ip route
          Codes: K - kernel route, C - connected, S - static, R - RIP,
                 B - BGP * - FIB route.
          
          K* 0.0.0.0/0              203.181.89.241
          S  0.0.0.0/0              203.181.89.1
          C* 127.0.0.0/8            lo
          C* 203.181.89.240/28      eth0

 - Command: show ipv6 route

 - Command: show interface

 - Command: show ipforward
     Display whether the host's IP forwarding function is enabled or
     not.  Almost any UNIX kernel can be configured with IP forwarding
     disabled.  If so, the box can't work as a router.

 - Command: show ipv6forward
     Display whether the host's IP v6 forwarding is enabled or not.


File: zebra.info,  Node: RIP,  Next: RIPng,  Prev: Zebra,  Up: Top

RIP
***

   RIP - Routing Information Protocol is widely deployed interior
gateway protocol.  RIP was developed in the 1970s at Xerox Labs as part
of the XNS routing protocol.  RIP is a "distance-vector" protocol and is
based on the "Bellman-Ford" algorithms.  As a distance-vector protocol,
RIP router send updates to its neighbors periodically, thus allowing
the convergence to a known topology.  In each update, the distance to
any given network will be broadcasted to its neighboring router.

   `ripd' supports RIP version 2 as described in RFC2453 and RIP
version 1 as described in RFC1058.

* Menu:

* Starting and Stopping ripd::
* RIP Configuration::
* How to Announce RIP route::
* Filtering RIP Routes::
* RIP Metric Manipulation::
* RIP distance::
* RIP route-map::
* RIP Authentication::
* RIP Timers::
* Show RIP Information::
* RIP Debug Commands::


File: zebra.info,  Node: Starting and Stopping ripd,  Next: RIP Configuration,  Prev: RIP,  Up: RIP

Starting and Stopping ripd
==========================

   The default configuration file name of `ripd''s is `ripd.conf'.
When invocation `ripd' searches directory /usr/local/etc.  If
`ripd.conf' is not there next search current directory.

   RIP uses UDP port 521 to send and receive RIP packets.  So the user
must have the capability to bind the port, generally this means that
the user must have superuser privileges.  RIP protocol requires
interface information maintained by `zebra' daemon.  So running `zebra'
is mandatory to run `ripd'.  Thus minimum sequence for running RIP is
like below:

     # zebra -d
     # ripd -d

   Please note that `zebra' must be invoked before `ripd'.

   To stop `ripd'.  Please use `kill `cat /var/run/ripd.pid`'.  Certain
signals have special meaningss to `ripd'.

`SIGHUP'
     Reload configuration file `ripd.conf'.  All configurations are
     reseted.  All routes learned so far are cleared and removed from
     routing table.

`SIGUSR1'
     Rotate `ripd' logfile.

`SIGINT'
`SIGTERM'
     `ripd' sweeps all installed RIP routes then terminates properly.

   `ripd' invocation options.  Common options that can be specified
(*note Common Invocation Options::).

`-r'
`--retain'
     When the program terminates, retain routes added by `ripd'.

* Menu:

* RIP netmask::


File: zebra.info,  Node: RIP netmask,  Prev: Starting and Stopping ripd,  Up: Starting and Stopping ripd

RIP netmask
-----------

   The netmask features of `ripd' support both version 1 and version 2
of RIP.  Version 1 of RIP originally contained no netmask information.
In RIP version 1, network classes were originally used to determine the
size of the netmask.  Class A networks use 8 bits of mask, Class B
networks use 16 bits of masks, while Class C networks use 24 bits of
mask.  Today, the most widely used method of a network mask is assigned
to the packet on the basis of the interface that received the packet.
Version 2 of RIP supports a variable length subnet mask (VLSM).  By
extending the subnet mask, the mask can be divided and reused.  Each
subnet can be used for different purposes such as large to middle size
LANs and WAN links.  Zebra `ripd' does not support the non-sequential
netmasks that are included in RIP Version 2.

   In a case of similar information with the same prefix and metric, the
old information will be suppressed.  Ripd does not currently support
equal cost multipath routing.


File: zebra.info,  Node: RIP Configuration,  Next: How to Announce RIP route,  Prev: Starting and Stopping ripd,  Up: RIP

RIP Configuration
=================

 - Command: router rip
     The `router rip' command is necessary to enable RIP.  To disable
     RIP, use the `no router rip' command.  RIP must be enabled before
     carrying out any of the RIP commands.

 - Command: no rouer rip
     Disable RIP.

   RIP can be configured to process either Version 1 or Version 2
packets, the default mode is Version 2.  If no version is specified,
then the RIP daemon will default to Version 2.  If RIP is set to Version
1, the setting "Version 1" will be displayed, but the setting "Version
2" will not be displayed whether or not Version 2 is set explicitly as
the version of RIP being used.

 - RIP Command: network NETWORK
 - RIP Command: no network NETWORK
     Set the RIP enable interface by NETWORK.  The interfaces which
     have addresses matching with NETWORK are enabled.

     This group of commands either enables or disables RIP interfaces
     between certain numbers of a specified network address.  For
     example, if the network for 10.0.0.0/24 is RIP enabled, this would
     result in all the addresses from 10.0.0.0 to 10.0.0.255 being
     enabled for RIP.  The `no network' command will disable RIP for
     the specified network.

 - RIP Command: network IFNAME
 - RIP Command: no network IFNAME
     Set a RIP enabled interface by IFNAME.  Both the sending and
     receiving of RIP packets will be enabled on the port specified in
     the `network ifname' command.  The `no network ifname' command
     will disable RIP on the specified interface.

 - RIP Command: neighbor A.B.C.D
 - RIP Command: no neighbor A.B.C.D
     Specify RIP neighbor.  When a neighbor doesn't understand
     multicast, this command is used to specify neighbors.  In some
     cases, not all routers will be able to understand multicasting,
     where packets are sent to a network or a group of addresses.  In a
     situation where a neighbor cannot process multicast packets, it is
     necessary to establish a direct link between routers.  The
     neighbor command allows the network administrator to specify a
     router as a RIP neighbor.  The `no neighbor a.b.c.d' command will
     disable the RIP neighbor.

   Below is very simple RIP configuration.  Interface `eth0' and
interface which address match to `10.0.0.0/8' are RIP enabled.

     !
     router rip
      network 10.0.0.0/8
      network eth0
     !

   Passive interface

 - RIP command: passive-interface IFNAME
 - RIP command: no passive-interface IFNAME
     This command sets the specified interface to passive mode.  On
     passive mode interface, all receiving packets are processed as
     normal and ripd does not send either multicast or unicast RIP
     packets except to RIP neighbors specified with `neighbor' command.

   RIP version handling

 - RIP Command: version VERSION
     Set RIP process's version.  VERSION can be "1" or "2".

 - Interface command: ip rip send version VERSION
     VERSION can be `1', `2', `1 2'.  This configuration command
     overrides the router's rip version setting.  The command will
     enable the selected interface to send packets with RIP Version 1,
     RIP Version 2, or both.  In the case of '1 2', packets will be
     both broadcast and multicast.

 - Interface command: ip rip receive version VERSION
     Version setting for incoming RIP packets.  This command will
     enable the selected interface to receive packets in RIP Version 1,
     RIP Version 2, or both.

   RIP split-horizon

 - Interface command: ip split-horizon
 - Interface command: no ip split-horizon
     Control split-horizon on the interface.  Default is `ip
     split-horizon'.  If you don't perform split-horizon on the
     interface, please specify `no ip split-horizon'.


File: zebra.info,  Node: How to Announce RIP route,  Next: Filtering RIP Routes,  Prev: RIP Configuration,  Up: RIP

How to Announce RIP route
=========================

 - RIP command: redistribute kernel
 - RIP command: redistribute kernel metric <0-16>
 - RIP command: redistribute kernel route-map ROUTE-MAP
 - RIP command: no redistribute kernel
     `redistribute kernel' redistributes routing information from
     kernel route entries into the RIP tables. `no redistribute kernel'
     disables the routes.

 - RIP command: redistribute static
 - RIP command: redistribute static metric <0-16>
 - RIP command: redistribute static route-map ROUTE-MAP
 - RIP command: no redistribute static
     `redistribute static' redistributes routing information from
     static route entries into the RIP tables. `no redistribute static'
     disables the routes.

 - RIP command: redistribute connected
 - RIP command: redistribute connected metric <0-16>
 - RIP command: redistribute connected route-map ROUTE-MAP
 - RIP command: no redistribute connected
     Redistribute connected routes into the RIP tables.  `no
     redistribute connected' disables the connected routes in the RIP
     tables.  This command redistribute connected of the interface
     which RIP disabled.  The connected route on RIP enabled interface
     is announced by default.

 - RIP command: redistribute ospf
 - RIP command: redistribute ospf metric <0-16>
 - RIP command: redistribute ospf route-map ROUTE-MAP
 - RIP command: no redistribute ospf
     `redistribute ospf' redistributes routing information from ospf
     route entries into the RIP tables. `no redistribute ospf' disables
     the routes.

 - RIP command: redistribute bgp
 - RIP command: redistribute bgp metric <0-16>
 - RIP command: redistribute bgp route-map ROUTE-MAP
 - RIP command: no redistribute bgp
     `redistribute bgp' redistributes routing information from bgp
     route entries into the RIP tables. `no redistribute bgp' disables
     the routes.

   If you want to specify RIP only static routes:

 - RIP command: default-information originate

 - RIP command: route A.B.C.D/M
 - RIP command: no route A.B.C.D/M
     This command is specific to Zebra.  The `route' command makes a
     static route only inside RIP. This command should be used only by
     advanced users who are particularly knowledgeable about the RIP
     protocol.  In most cases, we recommend creating a static route in
     Zebra and redistributing it in RIP using `redistribute static'.


File: zebra.info,  Node: Filtering RIP Routes,  Next: RIP Metric Manipulation,  Prev: How to Announce RIP route,  Up: RIP

Filtering RIP Routes
====================

   RIP routes can be filtered by a distribute-list.

 - Command: distribute-list ACCESS_LIST DIRECT IFNAME
     You can apply access lists to the interface with a
     `distribute-list' command.  ACCESS_LIST is the access list name.
     DIRECT is `in' or `out'.  If DIRECT is `in' the access list is
     applied to input packets.

     The `distribute-list' command can be used to filter the RIP path.
     `distribute-list' can apply access-lists to a chosen interface.
     First, one should specify the access-list.  Next, the name of the
     access-list is used in the distribute-list command.  For example,
     in the following configuration `eth0' will permit only the paths
     that match the route 10.0.0.0/8

          !
          router rip
           distribute-list private in eth0
          !
          access-list private permit 10 10.0.0.0/8
          access-list private deny any
          !

   `distribute-list' can be applied to both incoming and outgoing data.

 - Command: distribute-list prefix PREFIX_LIST (in|out) IFNAME
     You can apply prefix lists to the interface with a
     `distribute-list' command.  PREFIX_LIST is the prefix list name.
     Next is the direction of `in' or `out'.  If DIRECT is `in' the
     access list is applied to input packets.


File: zebra.info,  Node: RIP Metric Manipulation,  Next: RIP distance,  Prev: Filtering RIP Routes,  Up: RIP

RIP Metric Manipulation
=======================

   RIP metric is a value for distance for the network.  Usually `ripd'
increment the metric when the network information is received.
Redistributed routes' metric is set to 1.

 - RIP command: default-metric <1-16>
 - RIP command: no default-metric <1-16>
     This command modifies the default metric value for redistributed
     routes.  The default value is 1.  This command does not affect
     connected route even if it is redistributed by `redistribute
     connected'.  To modify connected route's metric value, please use
     `redistribute connected metric' or `route-map'.  `offset-list' also
     affects connected routes.

 - RIP command: offset-list ACCESS-LIST (in|out)
 - RIP command: offset-list ACCESS-LIST (in|out) IFNAME


File: zebra.info,  Node: RIP distance,  Next: RIP route-map,  Prev: RIP Metric Manipulation,  Up: RIP

RIP distance
============

   Distance value is used in zebra daemon.  Default RIP distance is 120.

 - RIP command: distance <1-255>
 - RIP command: no distance <1-255>
     Set default RIP distance to specified value.

 - RIP command: distance <1-255> A.B.C.D/M
 - RIP command: no distance <1-255> A.B.C.D/M
     Set default RIP distance to specified value when the route's
     source IP address matches the specified prefix.

 - RIP command: distance <1-255> A.B.C.D/M ACCESS-LIST
 - RIP command: no distance <1-255> A.B.C.D/M ACCESS-LIST
     Set default RIP distance to specified value when the route's
     source IP address matches the specified prefix and the specified
     access-list.


File: zebra.info,  Node: RIP route-map,  Next: RIP Authentication,  Prev: RIP distance,  Up: RIP

RIP route-map
=============

   Usage of `ripd''s route-map support.

   Optional argument route-map MAP_NAME can be added to each
`redistribute' statement.

     redistribute static [route-map MAP_NAME]
     redistribute connected [route-map MAP_NAME]
     .....

   Cisco applies route-map _before_ routes will exported to rip route
table.  In current Zebra's test implementation, `ripd' applies route-map
after routes are listed in the route table and before routes will be
announced to an interface (something like output filter). I think it is
not so clear, but it is draft and it may be changed at future.

   Route-map statement (*note Route Map::) is needed to use route-map
functionality.

 - Route Map: match interface WORD
     This command match to incoming interface.  Notation of this match
     is different from Cisco. Cisco uses a list of interfaces - NAME1
     NAME2 ... NAMEN.  Ripd allows only one name (maybe will change in
     the future).  Next - Cisco means interface which includes next-hop
     of routes (it is somewhat similar to "ip next-hop" statement).
     Ripd means interface where this route will be sent. This
     difference is because "next-hop" of same routes which sends to
     different interfaces must be different. Maybe it'd be better to
     made new matches - say "match interface-out NAME" or something
     like that.

 - Route Map: match ip address WORD
 - Route Map: match ip address prefix-list WORD
     Match if route destination is permitted by access-list.

 - Route Map: match ip next-hop A.B.C.D
     Cisco uses here <access-list>, `ripd' IPv4 address. Match if route
     has this next-hop (meaning next-hop listed in the rip route table
     - "show ip rip")

 - Route Map: match metric <0-4294967295>
     This command match to the metric value of RIP updates.  For other
     protocol compatibility metric range is shown as <0-4294967295>.
     But for RIP protocol only the value range <0-16> make sense.

 - Route Map: set ip next-hop A.B.C.D
     This command set next hop value in RIPv2 protocol.  This command
     does not affect RIPv1 because there is no next hop field in the
     packet.

 - Route Map: set metric <0-4294967295>
     Set a metric for matched route when sending announcement.  The
     metric value range is very large for compatibility with other
     protocols.  For RIP, valid metric values are from 1 to 16.


File: zebra.info,  Node: RIP Authentication,  Next: RIP Timers,  Prev: RIP route-map,  Up: RIP

RIP Authentication
==================

 - Interface command: ip rip authentication mode md5
 - Interface command: no ip rip authentication mode md5
     Set the interface with RIPv2 MD5 authentication.

 - Interface command: ip rip authentication mode text
 - Interface command: no ip rip authentication mode text
     Set the interface with RIPv2 simple password authentication.

 - Interface command: ip rip authentication string STRING
 - Interface command: no ip rip authentication string STRING
     RIP version 2 has simple text authentication.  This command sets
     authentication string.  The string must be shorter than 16
     characters.

 - Interface command: ip rip authentication key-chain KEY-CHAIN
 - Interface command: no ip rip authentication key-chain KEY-CHAIN
     Specifiy Keyed MD5 chain.

     !
     key chain test
      key 1
       key-string test
     !
     interface eth1
      ip rip authentication mode md5
      ip rip authentication key-chain test
     !


File: zebra.info,  Node: RIP Timers,  Next: Show RIP Information,  Prev: RIP Authentication,  Up: RIP

RIP Timers
==========

 - RIP command: timers basic UPDATE TIMEOUT GARBAGE
     RIP protocol has several timers.  User can configure those timers'
     values by `timers basic' command.

     The default settings for the timers are as follows:

        * The update timer is 30 seconds. Every update timer seconds,
          the RIP process is awakened to send an unsolicited Response
          message containing the complete routing table to all
          neighboring RIP routers.

        * The timeout timer is 180 seconds. Upon expiration of the
          timeout, the route is no longer valid; however, it is
          retained in the routing table for a short time so that
          neighbors can be notified that the route has been dropped.

        * The garbage collect timer is 120 seconds.  Upon expiration of
          the garbage-collection timer, the route is finally removed
          from the routing table.


     The `timers basic' command allows the the default values of the
     timers listed above to be changed.

 - RIP command: no timers basic
     The `no timers basic' command will reset the timers to the default
     settings listed above.


File: zebra.info,  Node: Show RIP Information,  Next: RIP Debug Commands,  Prev: RIP Timers,  Up: RIP

Show RIP Information
====================

   To display RIP routes.

 - Command: show ip rip
     Show RIP routes.

   The command displays all RIP routes. For routes that are received
through RIP, this command will display the time the packet was sent and
the tag information.  This command will also display this information
for routes redistributed into RIP.

 - Command: show ip protocols
     The command displays current RIP status.  It includes RIP timer,
     filtering, version, RIP enabled interface and RIP peer inforation.

     ripd> show ip protocols
     Routing Protocol is "rip"
       Sending updates every 30 seconds with +/-50%, next due in 35 seconds
       Timeout after 180 seconds, garbage collect after 120 seconds
       Outgoing update filter list for all interface is not set
       Incoming update filter list for all interface is not set
       Default redistribution metric is 1
       Redistributing: kernel connected
       Default version control: send version 2, receive version 2
         Interface        Send  Recv
       Routing for Networks:
         eth0
         eth1
         1.1.1.1
         203.181.89.241
       Routing Information Sources:
         Gateway          BadPackets BadRoutes  Distance Last Update


File: zebra.info,  Node: RIP Debug Commands,  Prev: Show RIP Information,  Up: RIP

RIP Debug Commands
==================

   Debug for RIP protocol.

 - Command: debug rip events
     Debug rip events.

   `debug rip' will show RIP events.  Sending and receiving packets,
timers, and changes in interfaces are events shown with `ripd'.

 - Command: debug rip packet
     Debug rip packet.

   `debug rip packet' will display detailed information about the RIP
packets.  The origin and port number of the packet as well as a packet
dump is shown.

 - Command: debug rip zebra
     Debug rip between zebra communication.

   This command will show the communication between `ripd' and `zebra'.
The main information will include addition and deletion of paths to the
kernel and the sending and receiving of interface information.

 - Command: show debugging rip
     Display `ripd''s debugging option.

   `show debugging rip' will show all information currently set for ripd
debug.


File: zebra.info,  Node: RIPng,  Next: OSPFv2,  Prev: RIP,  Up: Top

RIPng
*****

   `ripngd' supports the RIPng protocol as described in RFC2080.  It's
an IPv6 reincarnation of the RIP protocol.

* Menu:

* Invoking ripngd::
* ripngd Configuration::
* ripngd Terminal Mode Commands::
* ripngd Filtering Commands::


File: zebra.info,  Node: Invoking ripngd,  Next: ripngd Configuration,  Prev: RIPng,  Up: RIPng

Invoking ripngd
===============

   There are no `ripngd' specific invocation options.  Common options
can be specified (*note Common Invocation Options::).


File: zebra.info,  Node: ripngd Configuration,  Next: ripngd Terminal Mode Commands,  Prev: Invoking ripngd,  Up: RIPng

ripngd Configuration
====================

   Currently ripngd supports the following commands:

 - Command: router ripng
     Enable RIPng.

 - RIPng Command: flush_timer TIME
     Set flush timer.

 - RIPng Command: network NETWORK
     Set RIPng enabled interface by NETWORK

 - RIPng Command: network IFNAME
     Set RIPng enabled interface by IFNAME

 - RIPng Command: route NETWORK
     Set RIPng static routing announcement of NETWORK.

 - Command: router zebra
     This command is the default and does not appear in the
     configuration.  With this statement, RIPng routes go to the
     `zebra' daemon.


File: zebra.info,  Node: ripngd Terminal Mode Commands,  Next: ripngd Filtering Commands,  Prev: ripngd Configuration,  Up: RIPng

ripngd Terminal Mode Commands
=============================

 - Command: show ip ripng

 - Command: show debugging ripng

 - Command: debug ripng events

 - Command: debug ripng packet

 - Command: debug ripng zebra


File: zebra.info,  Node: ripngd Filtering Commands,  Prev: ripngd Terminal Mode Commands,  Up: RIPng

ripngd Filtering Commands
=========================

 - Command: distribute-list ACCESS_LIST (in|out) IFNAME
     You can apply an access-list to the interface using the
     `distribute-list' command.  ACCESS_LIST is an access-list name.
     DIRECT is `in' or `out'.  If DIRECT is `in', the access-list is
     applied only to incoming packets.

          distribute-list local-only out sit1


File: zebra.info,  Node: OSPFv2,  Next: OSPFv3,  Prev: RIPng,  Up: Top

OSPFv2
******

   OSPF version 2 is a routing protocol which described in RFC2328 -
`OSPF Version 2'.  OSPF is IGP (Interior Gateway Protocols).  Compared
with RIP, OSPF can provide scalable network support and faster
convergence time.  OSPF is widely used in large networks such as ISP
backbone and enterprise networks.

* Menu:

* Configuring ospfd::
* OSPF router::
* OSPF area::
* OSPF interface::
* Redistribute routes to OSPF::
* Showing OSPF information::
* Debugging OSPF::


File: zebra.info,  Node: Configuring ospfd,  Next: OSPF router,  Prev: OSPFv2,  Up: OSPFv2

Configuring ospfd
=================

   There is no `ospfd' specific options.  Common options can be
specified (*note Common Invocation Options::) to `ospfd'.  `ospfd'
needs interface information from `zebra'.  So please make it sure
`zebra' is running before invoking `ospfd'.

   Like other daemons, `ospfd' configuration is done in OSPF specific
configuration file `ospfd.conf'.


File: zebra.info,  Node: OSPF router,  Next: OSPF area,  Prev: Configuring ospfd,  Up: OSPFv2

OSPF router
===========

   To start OSPF process you have to specify the OSPF router.  As of
this writing, `ospfd' does not support multiple OSPF processes.

 - Command: router ospf
 - Command: no router ospf
     Enable or disable the OSPF process.  `ospfd' does not yet support
     multiple OSPF processes.  So you can not specify an OSPF process
     number.

 - OSPF Command: ospf router-id A.B.C.D
 - OSPF Command: no ospf router-id

 - OSPF Command: ospf abr-type TYPE
 - OSPF Command: no ospf abr-type TYPE
     TYPE can be cisco|ibm|shortcut|standard

 - OSPF Command: ospf rfc1583compatibility
 - OSPF Command: no ospf rfc1583compatibility

 - OSPF Command: passive interface INTERFACE
 - OSPF Command: no passive interface INTERFACE

 - OSPF Command: timers spf <0-4294967295> <0-4294967295>
 - OSPF Command: no timers spf

 - OSPF Command: refresh group-limit <0-10000>
 - OSPF Command: refresh per-slice <0-10000>
 - OSPF Command: refresh age-diff <0-10000>

 - OSPF Command: auto-cost refrence-bandwidth <1-4294967>
 - OSPF Command: no auto-cost refrence-bandwidth

 - OSPF Command: network A.B.C.D/M area A.B.C.D
 - OSPF Command: network A.B.C.D/M area <0-4294967295>
 - OSPF Command: no network A.B.C.D/M area A.B.C.D
 - OSPF Command: no network A.B.C.D/M area <0-4294967295>
     This command specifies the OSPF enabled interface.  If the
     interface has an address of 10.0.0.1/8 then the command below
     provides network information to the ospf routers
          router ospf
           network 10.0.0.0/8 area 0
     the network command's mask length should be the same as the
     interface address's mask.


File: zebra.info,  Node: OSPF area,  Next: OSPF interface,  Prev: OSPF router,  Up: OSPFv2

OSPF area
=========

 - OSPF Command: area A.B.C.D range A.B.C.D/M
 - OSPF Command: area <0-4294967295> range A.B.C.D/M
 - OSPF Command: no area A.B.C.D range A.B.C.D/M
 - OSPF Command: no area <0-4294967295> range A.B.C.D/M

 - OSPF Command: area A.B.C.D range IPV4_PREFIX suppress
 - OSPF Command: no area A.B.C.D range IPV4_PREFIX suppress
 - OSPF Command: area A.B.C.D range IPV4_PREFIX substitute IPV4_PREFIX
 - OSPF Command: no area A.B.C.D range IPV4_PREFIX substitute
IPV4_PREFIX

 - OSPF Command: area A.B.C.D virtual-link A.B.C.D
 - OSPF Command: area <0-4294967295> virtual-link A.B.C.D
 - OSPF Command: no area A.B.C.D virtual-link A.B.C.D
 - OSPF Command: no area <0-4294967295> virtual-link A.B.C.D

 - OSPF Command: area A.B.C.D shortcut
 - OSPF Command: area <0-4294967295> shortcut
 - OSPF Command: no area A.B.C.D shortcut
 - OSPF Command: no area <0-4294967295> shortcut

 - OSPF Command: area A.B.C.D stub
 - OSPF Command: area <0-4294967295> stub
 - OSPF Command: no area A.B.C.D stub
 - OSPF Command: no area <0-4294967295> stub

 - OSPF Command: area A.B.C.D stub no-summary
 - OSPF Command: area <0-4294967295> stub no-summary
 - OSPF Command: no area A.B.C.D stub no-summary
 - OSPF Command: no area <0-4294967295> stub no-summary

 - OSPF Command: area A.B.C.D default-cost <0-16777215>
 - OSPF Command: no area A.B.C.D default-cost <0-16777215>

 - OSPF Command: area A.B.C.D export-list NAME
 - OSPF Command: area <0-4294967295> export-list NAME
 - OSPF Command: no area A.B.C.D export-list NAME
 - OSPF Command: no area <0-4294967295> export-list NAME

 - OSPF Command: area A.B.C.D import-list NAME
 - OSPF Command: area <0-4294967295> import-list NAME
 - OSPF Command: no area A.B.C.D import-list NAME
 - OSPF Command: no area <0-4294967295> import-list NAME

 - OSPF Command: area A.B.C.D authentication
 - OSPF Command: area <0-4294967295> authentication
 - OSPF Command: no area A.B.C.D authentication
 - OSPF Command: no area <0-4294967295> authentication

 - OSPF Command: area A.B.C.D authentication message-digest
 - OSPF Command: area <0-4294967295> authentication message-digest


File: zebra.info,  Node: OSPF interface,  Next: Redistribute routes to OSPF,  Prev: OSPF area,  Up: OSPFv2

OSPF interface
==============

 - Interface Command: ip ospf authentication-key AUTH_KEY
 - Interface Command: no ip ospf authentication-key
     Set OSPF authentication key to a simple password.  After setting
     AUTH_KEY, all OSPF packets are authenticated. AUTH_KEY has length
     up to 8 chars.

 - Interface Command: ip ospf message-digest-key KEYID md5 KEY
 - Interface Command: no ip ospf message-digest-key
     Set OSPF authentication key to a cryptographic password.  The
     cryptographic algorithm is MD5.  KEYID identifies secret key used
     to create the message digest.  KEY is the actual message digest
     key up to 16 chars.

 - Interface Command: ip ospf cost <1-65535>
 - Interface Command: no ip ospf cost
     Set link cost for the specified interface.  The cost value is set
     to router-LSA's metric field and used for SPF calculation.

 - Interface Command: ip ospf dead-interval <1-65535>
 - Interface Command: no ip ospf dead-interval
     Set number of seconds for RouterDeadInterval timer value used for
     Wait Timer and Inactivity Timer.  This value must be the same for
     all routers attached to a common network.  The default value is 40
     seconds.

 - Interface Command: ip ospf hello-interval <1-65535>
 - Interface Command: no ip ospf hello-interval
     Set number of seconds for HelloInterval timer value.  Setting this
     value, Hello packet will be sent every timer value seconds on the
     specified interface.  This value must be the same for all routers
     attached to a common network.  The default value is 10 seconds.

 - Interface Command: ip ospf network
(broadcast|non-broadcast|point-to-multipoint|point-to-point)
 - Interface Command: no ip ospf network
     Set explicitly network type for specifed interface.

 - Interface Command: ip ospf priority <0-255>
 - Interface Command: no ip ospf priority
     Set RouterPriority integer value.  Setting higher value, router
     will be more eligible to become Designated Router.  Setting the
     value to 0, router is no longer eligible to Designated Router.
     The default value is 1.

 - Interface Command: ip ospf retransmit-interval <1-65535>
 - Interface Command: no ip ospf retransmit interval
     Set number of seconds for RxmtInterval timer value.  This value is
     used when retransmitting Database Description and Link State
     Request packets.  The default value is 5 seconds.

 - Interface Command: ip ospf transmit-delay
 - Interface Command: no ip ospf transmit-delay
     Set number of seconds for InfTransDelay value.  LSAs' age should be
     incremented by this value when transmitting.  The default value is
     1 seconds.


File: zebra.info,  Node: Redistribute routes to OSPF,  Next: Showing OSPF information,  Prev: OSPF interface,  Up: OSPFv2

Redistribute routes to OSPF
===========================

 - OSPF Command: redistribute (kernel|connected|static|rip|bgp)
 - OSPF Command: redistribute (kernel|connected|static|rip|bgp)
ROUTE-MAP
 - OSPF Command: redistribute (kernel|connected|static|rip|bgp)
metric-type (1|2)
 - OSPF Command: redistribute (kernel|connected|static|rip|bgp)
metric-type (1|2) route-map WORD
 - OSPF Command: redistribute (kernel|connected|static|rip|bgp) metric
<0-16777214>
 - OSPF Command: redistribute (kernel|connected|static|rip|bgp) metric
<0-16777214> route-map WORD
 - OSPF Command: redistribute (kernel|connected|static|rip|bgp)
metric-type (1|2) metric <0-16777214>
 - OSPF Command: redistribute (kernel|connected|static|rip|bgp)
metric-type (1|2) metric <0-16777214> route-map WORD
 - OSPF Command: no redistribute (kernel|connected|static|rip|bgp)

 - OSPF Command: default-information originate
 - OSPF Command: default-information originate metric <0-16777214>
 - OSPF Command: default-information originate metric <0-16777214>
metric-type (1|2)
 - OSPF Command: default-information originate metric <0-16777214>
metric-type (1|2) route-map WORD
 - OSPF Command: default-information originate always
 - OSPF Command: default-information originate always metric
<0-16777214>
 - OSPF Command: default-information originate always metric
<0-16777214> metric-type (1|2)
 - OSPF Command: default-information originate always metric
<0-16777214> metric-type (1|2) route-map WORD
 - OSPF Command: no default-information originate

 - OSPF Command: distribute-list NAME out
(kernel|connected|static|rip|ospf
 - OSPF Command: no distribute-list NAME out
(kernel|connected|static|rip|ospf

 - OSPF Command: default-metric <0-16777214>
 - OSPF Command: no default-metric

 - OSPF Command: distance <1-255>
 - OSPF Command: no distance <1-255>

 - OSPF Command: distance ospf (intra-area|inter-area|external) <1-255>
 - OSPF Command: no distance ospf

 - Command: router zebra
 - Command: no router zebra


File: zebra.info,  Node: Showing OSPF information,  Next: Debugging OSPF,  Prev: Redistribute routes to OSPF,  Up: OSPFv2

Showing OSPF information
========================

 - Command: show ip ospf

 - Command: show ip ospf interface [INTERFACE]

 - Command: show ip ospf neighbor
 - Command: show ip ospf neighbor INTERFACE
 - Command: show ip ospf neighbor detail
 - Command: show ip ospf neighbor INTERFACE detail

 - Command: show ip ospf database

 - Command: show ip ospf database
(asbr-summary|external|network|router|summary)
 - Command: show ip ospf database
(asbr-summary|external|network|router|summary) LINK-STATE-ID
 - Command: show ip ospf database
(asbr-summary|external|network|router|summary) LINK-STATE-ID adv-router
ADV-ROUTER
 - Command: show ip ospf database
(asbr-summary|external|network|router|summary) adv-router ADV-ROUTER
 - Command: show ip ospf database
(asbr-summary|external|network|router|summary) LINK-STATE-ID
self-originate
 - Command: show ip ospf database
(asbr-summary|external|network|router|summary) self-originate

 - Command: show ip ospf database max-age

 - Command: show ip ospf database self-originate

 - Command: show ip ospf refresher

 - Command: show ip ospf route


File: zebra.info,  Node: Debugging OSPF,  Prev: Showing OSPF information,  Up: OSPFv2

Debugging OSPF
==============

 - Command: debug ospf packet
(hello|dd|ls-request|ls-update|ls-ack|all) (send|recv) [detail]
 - Command: no debug ospf packet
(hello|dd|ls-request|ls-update|ls-ack|all) (send|recv) [detail]

 - Command: debug ospf ism
 - Command: debug ospf ism (status|events|timers)
 - Command: no debug ospf ism
 - Command: no debug ospf ism (status|events|timers)

 - Command: debug ospf nsm
 - Command: debug ospf nsm (status|events|timers)
 - Command: no debug ospf nsm
 - Command: no debug ospf nsm (status|events|timers)

 - Command: debug ospf lsa
 - Command: debug ospf lsa (generate|flooding|refresh)
 - Command: no debug ospf lsa
 - Command: no debug ospf lsa (generate|flooding|refresh)

 - Command: debug ospf zebra
 - Command: debug ospf zebra (interface|redistribute)
 - Command: no debug ospf zebra
 - Command: no debug ospf zebra (interface|redistribute)

 - Command: show debugging ospf


File: zebra.info,  Node: OSPFv3,  Next: BGP,  Prev: OSPFv2,  Up: Top

OSPFv3
******

   `ospf6d' is a daemon support OSPF version 3 for IPv6 network.  OSPF
for IPv6 is described in RFC2740.

* Menu:

* OSPF6 router::
* OSPF6 area::
* OSPF6 interface::
* Redistribute routes to OSPF6::
* Showing OSPF6 information::


File: zebra.info,  Node: OSPF6 router,  Next: OSPF6 area,  Prev: OSPFv3,  Up: OSPFv3

OSPF6 router
============

 - Command: router ospf6

 - OSPF6 Command: router-id A.B.C.D
     Set router's Router-ID.

 - OSPF6 Command: interface IFNAME area AREA
     Bind interface to specified area, and start sending OSPF packets.
     AREA can be specified as 0.


File: zebra.info,  Node: OSPF6 area,  Next: OSPF6 interface,  Prev: OSPF6 router,  Up: OSPFv3

OSPF6 area
==========

   Area support for OSPFv3 is not yet implemented.


File: zebra.info,  Node: OSPF6 interface,  Next: Redistribute routes to OSPF6,  Prev: OSPF6 area,  Up: OSPFv3

OSPF6 interface
===============

 - Interface Command: ipv6 ospf6 cost COST
     Sets interface's output cost.  Default value is 1.

 - Interface Command: ipv6 ospf6 hello-interval HELLOINTERVAL
     Sets interface's Hello Interval.  Default 40

 - Interface Command: ipv6 ospf6 dead-interval DEADINTERVAL
     Sets interface's Router Dead Interval.  Default value is 40.

 - Interface Command: ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL
     Sets interface's Rxmt Interval.  Default value is 5.

 - Interface Command: ipv6 ospf6 priority PRIORITY
     Sets interface's Router Priority.  Default value is 1.

 - Interface Command: ipv6 ospf6 transmit-delay TRANSMITDELAY
     Sets interface's Inf-Trans-Delay.  Default value is 1.


File: zebra.info,  Node: Redistribute routes to OSPF6,  Next: Showing OSPF6 information,  Prev: OSPF6 interface,  Up: OSPFv3

Redistribute routes to OSPF6
============================

 - OSPF6 Command: redistribute static
 - OSPF6 Command: redistribute connected
 - OSPF6 Command: redistribute ripng


File: zebra.info,  Node: Showing OSPF6 information,  Prev: Redistribute routes to OSPF6,  Up: OSPFv3

Showing OSPF6 information
=========================

 - Command: show ipv6 ospf6 [INSTANCE_ID]
     INSTANCE_ID is an optional OSPF instance ID. To see router ID and
     OSPF instance ID, simply type "show ipv6 ospf6 <cr>".

 - Command: show ipv6 ospf6 database
     This command shows LSA database summary.  You can specify the type
     of LSA.

 - Command: show ipv6 ospf6 interface
     To see OSPF interface configuration like costs.

 - Command: show ipv6 ospf6 neighbor
     Shows state and chosen (Backup) DR of neighbor.

 - Command: show ipv6 ospf6 request-list A.B.C.D
     Shows requestlist of neighbor.

 - Command: show ipv6 route ospf6
     This command shows internal routing table.


File: zebra.info,  Node: BGP,  Next: VTY shell,  Prev: OSPFv3,  Up: Top

BGP
***

   BGP stands for a Border Gateway Protocol.  The lastest BGP version
is 4.  It is referred as BGP-4.  BGP-4 is one of the Exterior Gateway
Protocols and de-fact standard of Inter Domain routing protocol.  BGP-4
is described in `RFC1771' - `A Border Gateway Protocol 4 (BGP-4)'.

   Many extentions are added to `RFC1771'.  `RFC2858' - `Multiprotocol
Extensions for BGP-4' provide multiprotocol support to BGP-4.

* Menu:

* Starting BGP::
* BGP router::
* BGP network::
* BGP Peer::
* BGP Peer Group::
* BGP Address Family::
* Autonomous System::
* BGP Communities Attribute::
* BGP Extended Communities Attribute::
* Displaying BGP routes::
* Capability Negotiation::
* Route Reflector::
* Route Server::
* How to set up a 6-Bone connection::
* Dump BGP packets and table::


File: zebra.info,  Node: Starting BGP,  Next: BGP router,  Prev: BGP,  Up: BGP

Starting BGP
============

   Default configuration file of `bgpd' is `bgpd.conf'.  `bgpd'
searches the current directory first then /usr/local/etc/bgpd.conf.
All of bgpd's command must be configured in `bgpd.conf'.

   `bgpd' specific invocation options are described below.  Common
options may also be specified (*note Common Invocation Options::).

`-p PORT'
`--bgp_port=PORT'
     Set the bgp protocol's port number.

`-r'
`--retain'
     When program terminates, retain BGP routes added by zebra.


File: zebra.info,  Node: BGP router,  Next: BGP network,  Prev: Starting BGP,  Up: BGP

BGP router
==========

   First of all you must configure BGP router with `router bgp'
command.  To configure BGP router, you need AS number.  AS number is an
identification of autonomous system.  BGP protocol uses the AS number
for detecting whether the BGP connection is internal one or external
one.

 - Command: router bgp ASN
     Enable a BGP protocol process with the specified ASN.  After this
     statement you can input any `BGP Commands'.  You can not create
     different BGP process under different ASN without specifying
     `multiple-instance' (*note Multiple instance::).

 - Command: no router bgp ASN
     Destroy a BGP protocol process with the specified ASN.

 - BGP: bgp router-id A.B.C.D
     This command specifies the router-ID.  If `bgpd' connects to
     `zebra' it gets interface and address information.  In that case
     default router ID value is selected as the largest IP Address of
     the interfaces.  When `router zebra' is not enabled `bgpd' can't
     get interface information so `router-id' is set to 0.0.0.0.  So
     please set router-id by hand.

* Menu:

* BGP distance::
* BGP decision process::


File: zebra.info,  Node: BGP distance,  Next: BGP decision process,  Prev: BGP router,  Up: BGP router

BGP distance
------------

 - BGP: distance bgp <1-255> <1-255> <1-255>
     This command change distance value of BGP.  Each argument is
     distance value for external routes, internal routes and local
     routes.

 - BGP: distance <1-255> A.B.C.D/M
 - BGP: distance <1-255> A.B.C.D/M WORD
     This command set distance value to


File: zebra.info,  Node: BGP decision process,  Prev: BGP distance,  Up: BGP router

BGP decision process
--------------------

1. Weight check

2. Local preference check.

3. Local route check.

4. AS path length check.

5. Origin check.

6. MED check.

File: zebra.info,  Node: BGP network,  Next: BGP Peer,  Prev: BGP router,  Up: BGP

BGP network
===========

* Menu:

* BGP route::
* Route Aggregation::
* Redistribute to BGP::


File: zebra.info,  Node: BGP route,  Next: Route Aggregation,  Prev: BGP network,  Up: BGP network

BGP route
---------

 - BGP: network A.B.C.D/M
     This command adds the announcement network.
          router bgp 1
           network 10.0.0.0/8
     This configuration example says that network 10.0.0.0/8 will
     be announced to all neighbors.  Some vendors' routers don't
     advertise routes if they aren't present in their IGP routing
     tables; `bgp' doesn't care about IGP routes when announcing its
     routes.

 - BGP: no network A.B.C.D/M


File: zebra.info,  Node: Route Aggregation,  Next: Redistribute to BGP,  Prev: BGP route,  Up: BGP network

Route Aggregation
-----------------

 - BGP: aggregate-address A.B.C.D/M
     This command specifies an aggregate address.

 - BGP: aggregate-address A.B.C.D/M as-set
     This command specifies an aggregate address.  Resulting routes
     inlucde AS set.

 - BGP: aggregate-address A.B.C.D/M summary-only
     This command specifies an aggregate address.  Aggreated routes will
     not be announce.

 - BGP: no aggregate-address A.B.C.D/M


File: zebra.info,  Node: Redistribute to BGP,  Prev: Route Aggregation,  Up: BGP network

Redistribute to BGP
-------------------

 - BGP: redistribute kernel
     Redistribute kernel route to BGP process.

 - BGP: redistribute static
     Redistribute static route to BGP process.

 - BGP: redistribute connected
     Redistribute connected route to BGP process.

 - BGP: redistribute rip
     Redistribute RIP route to BGP process.

 - BGP: redistribute ospf
     Redistribute OSPF route to BGP process.


File: zebra.info,  Node: BGP Peer,  Next: BGP Peer Group,  Prev: BGP network,  Up: BGP

BGP Peer
========

* Menu:

* Defining Peer::
* BGP Peer commands::
* Peer filtering::


File: zebra.info,  Node: Defining Peer,  Next: BGP Peer commands,  Prev: BGP Peer,  Up: BGP Peer

Defining Peer
-------------

 - BGP: neighbor PEER remote-as ASN
     Creates a new neighbor whose remote-as is ASN.  PEER can be an
     IPv4 address or an IPv6 address.
          router bgp 1
           neighbor 10.0.0.1 remote-as 2
     In this case my router, in AS-1, is trying to peer with AS-2
     at 10.0.0.1.

     This command must be the first command used when configuring a
     neighbor.  If the remote-as is not specified, `bgpd' will complain
     like this:
          can't find neighbor 10.0.0.1


File: zebra.info,  Node: BGP Peer commands,  Next: Peer filtering,  Prev: Defining Peer,  Up: BGP Peer

BGP Peer commands
-----------------

   In a `router bgp' clause there are neighbor specific configurations
required.

 - BGP: neighbor PEER shutdown
 - BGP: no neighbor PEER shutdown
     Shutdown the peer.  We can delete the neighbor's configuration by
     `no neighbor PEER remote-as AS-NUMBER' but all configuration of
     the neighbor will be deleted.  When you want to preserve the
     configuration, but want to drop the BGP peer, use this syntax.

 - BGP: neighbor PEER ebgp-multihop
 - BGP: no neighbor PEER ebgp-multihop

 - BGP: neighbor PEER description ...
 - BGP: no neighbor PEER description ...
     Set description of the peer.

 - BGP: neighbor PEER version VERSION
     Set up the neighbor's BGP version.  VERSION can be 4, 4+ or 4-.
     BGP version 4 is the default value used for BGP peering.  BGP
     version 4+ means that the neighbor supports Multiprotocol
     Extensions for BGP-4.  BGP version 4- is similar but the neighbor
     speaks the old Internet-Draft revision 00's Multiprotocol
     Extensions for BGP-4.  Some routing software is still using this
     version.

 - BGP: neighbor PEER interface IFNAME
 - BGP: no neighbor PEER interface IFNAME
     When you connect to a BGP peer over an IPv6 link-local address,
     you have to specify the IFNAME of the interface used for the
     connection.

 - BGP: neighbor PEER next-hop-self
 - BGP: no neighbor PEER next-hop-self
     This command specifies an announced route's nexthop as being
     equivalent to the address of the bgp router.

 - BGP: neighbor PEER update-source
 - BGP: no neighbor PEER update-source

 - BGP: neighbor PEER default-originate
 - BGP: no neighbor PEER default-originate
     `bgpd''s default is to not announce the default route (0.0.0.0/0)
     even it is in routing table.  When you want to announce default
     routes to the peer, use this command.

 - BGP: neighbor PEER port PORT
 - BGP: neighbor PEER port PORT

 - BGP: neighbor PEER send-community
 - BGP: neighbor PEER send-community

 - BGP: neighbor PEER weight WEIGHT
 - BGP: no neighbor PEER weight WEIGHT
     This command specifies a default WEIGHT value for the neighbor's
     routes.

 - BGP: neighbor PEER maximum-prefix NUMBER
 - BGP: no neighbor PEER maximum-prefix NUMBER


File: zebra.info,  Node: Peer filtering,  Prev: BGP Peer commands,  Up: BGP Peer

Peer filtering
--------------

 - BGP: neighbor PEER distribute-list NAME [in|out]
     This command specifies a distribute-list for the peer.  DIRECT is
     `in' or `out'.

 - BGP command: neighbor PEER prefix-list NAME [in|out]

 - BGP command: neighbor PEER filter-list NAME [in|out]

 - BGP: neighbor PEER route-map NAME [in|out]
     Apply a route-map on the neighbor.  DIRECT must be `in' or `out'.


File: zebra.info,  Node: BGP Peer Group,  Next: BGP Address Family,  Prev: BGP Peer,  Up: BGP

BGP Peer Group
==============

 - BGP: neighbor WORD peer-group
     This command defines a new peer group.

 - BGP: neighbor PEER peer-group WORD
     This command bind specific peer to peer group WORD.


File: zebra.info,  Node: BGP Address Family,  Next: Autonomous System,  Prev: BGP Peer Group,  Up: BGP

BGP Address Family
==================


File: zebra.info,  Node: Autonomous System,  Next: BGP Communities Attribute,  Prev: BGP Address Family,  Up: BGP

Autonomous System
=================

   AS (Autonomous System) is one of the essential element of BGP.  BGP
is a distance vector routing protocol.  AS framework provides distance
vector metric and loop detection to BGP.  And also AS can provide
policy routing by AS path prepend.  `RFC1930' - `Guidelines for
creation, selection, and registration of an Autonomous System (AS)'
describes how to use AS.

   AS number is tow octet.  It's value range is from 1 to 65535.  AS
numbers 64512 through 65535 are defined as private AS numbers.  Private
AS numbers must not to be advertised in the global Internet.

* Menu:

* AS Path Regular Expression::
* Display BGP Routes by AS Path::
* AS Path Access List::
* Using AS Path in Route Map::
* Private AS Numbers::


File: zebra.info,  Node: AS Path Regular Expression,  Next: Display BGP Routes by AS Path,  Prev: Autonomous System,  Up: Autonomous System

AS Path Regular Expression
--------------------------

   AS path regular expression can be used for displaying BGP routes and
AS path access list.  AS path regular expression is based on `POSIX
1003.2' regular expressions.  Following description is just a subset of
`POSIX' regular expression.  User can use full `POSIX' regular
expression.  Adding to that special character '_' is added for AS path
regular expression.

`.'
     Matches any single character.

`*'
     Matches 0 or more occurrences of pattern.

`+'
     Matches 1 or more occurrences of pattern.

`?'
     Match 0 or 1 occurrences of pattern.

`^'
     Matches the beginning of the line.

`$'
     Matches the end of the line.

`_'
     Character `_' has special meanings in AS path regular expression.
     It matches to space and comma , and AS set delimiter { and } and AS
     confederation delimiter `(' and `)'.  And it also matches to the
     beginning of the line and the end of the line.


File: zebra.info,  Node: Display BGP Routes by AS Path,  Next: AS Path Access List,  Prev: AS Path Regular Expression,  Up: Autonomous System

Display BGP Routes by AS Path
-----------------------------

   To show BGP routes which has specific AS path information `show ip
bgp' command can be used.

 - Command: show ip bgp regexp LINE
     This commands display BGP routes that matches AS path regular
     expression LINE.


File: zebra.info,  Node: AS Path Access List,  Next: Using AS Path in Route Map,  Prev: Display BGP Routes by AS Path,  Up: Autonomous System

AS Path Access List
-------------------

   AS path access list is user defined AS path.

 - Command: ip as-path access-list WORD {permit|deny} LINE
     This command defines a new AS path access list.

 - Command: no ip as-path access-list WORD
 - Command: no ip as-path access-list WORD {permit|deny} LINE


File: zebra.info,  Node: Using AS Path in Route Map,  Next: Private AS Numbers,  Prev: AS Path Access List,  Up: Autonomous System

Using AS Path in Route Map
--------------------------

 - Route Map: match as-path WORD

 - Route Map: set as-path prepend AS-PATH


File: zebra.info,  Node: Private AS Numbers,  Prev: Using AS Path in Route Map,  Up: Autonomous System

Private AS Numbers
------------------


File: zebra.info,  Node: BGP Communities Attribute,  Next: BGP Extended Communities Attribute,  Prev: Autonomous System,  Up: BGP

BGP Communities Attribute
=========================

   BGP communities attribute is widely used for implementing policy
routing.  Network operators can manipulate BGP communities attribute
based on their network policy.  BGP communities attribute is defined in
`RFC1997' - `BGP Communities Attribute' and `RFC1998' - `An Application
of the BGP Community Attribute in Multi-home Routing'.  It is an
optional transitive attribute, therefore local policy can travel
through different autonomous system.

   Communities attribute is a set of communities values.  Each
communities value is 4 octet long.  The following format is used to
define communities value.

`AS:VAL'
     This format represents 4 octet communities value.  `AS' is high
     order 2 octet in digit format.  `VAL' is low order 2 octet in
     digit format.  This format is useful to define AS oriented policy
     value.  For example, `7675:80' can be used when AS 7675 wants to
     pass local policy value 80 to neighboring peer.

`internet'
     `internet' represents well-known communities value 0.

`no-export'
     `no-export' represents well-known communities value `NO_EXPORT'
     (0xFFFFFF01).  All routes carry this value must not be advertised
     to outside a BGP confederation boundary.  If neighboring BGP peer
     is part of BGP confederation, the peer is considered as inside a
     BGP confederation boundary, so the route will be announced to the
     peer.

`no-advertise'
     `no-advertise' represents well-known communities value
     `NO_ADVERTISE'
     (0xFFFFFF02).  All routes carry this value must not be advertise
     to other BGP peers.

`local-AS'
     `local-AS' represents well-known communities value
     `NO_EXPORT_SUBCONFED' (0xFFFFFF03).  All routes carry this value
     must not be advertised to external BGP peers.  Even if the
     neighboring router is part of confederation, it is considered as
     external BGP peer, so the route will not be announced to the peer.

   When BGP communities attribute is received, duplicated communities
value in the communities attribute is ignored and each communities
values are sorted in numerical order.

* Menu:

* BGP Community Lists::
* Numbered BGP Community Lists::
* BGP Community in Route Map::
* Display BGP Routes by Community::
* Using BGP Communities Attribute::


File: zebra.info,  Node: BGP Community Lists,  Next: Numbered BGP Community Lists,  Prev: BGP Communities Attribute,  Up: BGP Communities Attribute

BGP Community Lists
-------------------

   Community-list is a user defined BGP communites attribute list.
Community-list can be used for matching or manipulating BGP communities
attribute in BGP updates.

   There are two types of community-list.  One is standard
community-list and another is expanded community-list.  Standard
community-list defines communities attribute.  Expanded community-list
defines communities attribute string with regular expression.  Standard
community-list is compiled into binary format when user define it.
Standard community-list will be directly compared to BGP communities
attribute in BGP updates.  Therefore the comparison is faster than
expanded community-list.

 - Command: ip community-list standard NAME {permit|deny} COMMUNITY
     This command defines a new standard community-list.  COMMUNITY is
     communities value.  The COMMUNITY is compiled into community
     structure.  We can define multiple community-list under same name.
     In that case match will happen user defined order.  Once the
     community-list matches to communities attribute in BGP updates it
     return permit or deny by the community-list definition.  When
     there is no matched entry, deny will be returned.  When COMMUNITY
     is empty it matches to any routes.

 - Command: ip community-list expanded NAME {permit|deny} LINE
     This command defines a new expanded community-list.  LINE is a
     string expression of communities attribute.  LINE can include
     regular expression to match communities attribute in BGP updates.

 - Command: no ip community-list NAME
 - Command: no ip community-list standard NAME
 - Command: no ip community-list expanded NAME
     These commands delete community lists specified by NAME.  All of
     community lists shares a single name space.  So community lists
     can be removed simpley specifying community lists name.

 - Command: show ip community-list
 - Command: show ip community-list NAME
     This command display current community-list information.  When
     NAME is specified the specified community list's information is
     shown.

          # show ip community-list
          Named Community standard list CLIST
              permit 7675:80 7675:100 no-export
              deny internet
          Named Community expanded list EXPAND
              permit :
          
          # show ip community-list CLIST
          Named Community standard list CLIST
              permit 7675:80 7675:100 no-export
              deny internet


File: zebra.info,  Node: Numbered BGP Community Lists,  Next: BGP Community in Route Map,  Prev: BGP Community Lists,  Up: BGP Communities Attribute

Numbered BGP Community Lists
----------------------------

   When number is used for BGP community lists name, the number has
special meanings.  Community list number in the range from 1 and 99 is
standard community-list.  Community list number in the range from 100
to 199 is expanded community-list.  These community lists are called as
numbered community lists.  On the other hand normal community lists is
called as named community lists.

 - Command: ip community-list <1-99> {permit|deny} COMMUNITY
     This command defines a new community-list.  <1-99> is standard
     community-list number.  Community-list name within this range
     defines standard community list.  When COMMUNITY is empty it
     matches to any routes.

 - Command: ip community-list <100-199> {permit|deny} COMMUNITY
     This command defines a new community-list.  <100-199> is expanded
     community-list number.  Community-list name within this range
     defines expanded community list.

 - Command: ip community-list NAME {permit|deny} COMMUNITY
     When community list type is not specifed, the community list type
     is automatically detected.  If COMMUNITY can be compiled into
     communities attribute, the community list is defined as a standard
     community list.  Otherwise it is defined as an expanded community
     list.  This feature is left for backward compability.  Use of this
     feature is not recommended.


File: zebra.info,  Node: BGP Community in Route Map,  Next: Display BGP Routes by Community,  Prev: Numbered BGP Community Lists,  Up: BGP Communities Attribute

BGP Community in Route Map
--------------------------

   In Route Map (*note Route Map::), we can match or set BGP
communities attribute.  Using this feature network operator can
implement their network policy based on BGP communities attribute.

   Following commands can be used in Route Map.

 - Route Map: match community WORD
 - Route Map: match community WORD exact-match
     This command perform match to BGP updates using community list
     WORD.  When the one of BGP communities value match to the one of
     communities value in community list, it is match.  When
     `exact-match' keyword is spcified, match happen only when BGP
     updates have completely same communities value specified in the
     community list.

 - Route Map: set community none
 - Route Map: set community COMMUNITY
 - Route Map: set community COMMUNITY additive
     This command manipulate communities value in BGP updates.  When
     `none' is specified as communities value, it removes entire
     communities attribute from BGP updates.  When COMMUNITY is not
     `none', specified communities value is set to BGP updates.  If BGP
     updates already has BGP communities value, the existing BGP
     communities value is replaced with specified COMMUNITY value.
     When `additive' keyword is specified, COMMUNITY is appended to the
     existing communities value.

 - Route Map: set comm-list WORD delete
     This command remove communities value from BGP communities
     attribute.  The WORD is community list name.  When BGP route's
     communities value matches to the community list WORD, the
     communities value is removed.  When all of communities value is
     removed eventually, the BGP update's communities attribute is
     completely removed.


File: zebra.info,  Node: Display BGP Routes by Community,  Next: Using BGP Communities Attribute,  Prev: BGP Community in Route Map,  Up: BGP Communities Attribute

Display BGP Routes by Community
-------------------------------

   To show BGP routes which has specific BGP communities attribute,
`show ip bgp' command can be used.  The COMMUNITY value and community
list can be used for `show ip bgp' command.

 - Command: show ip bgp community COMMUNITY
 - Command: show ip bgp community COMMUNITY exact-match
     This commands display BGP routes that matches COMMUNITY value.
     For this command, `internet' keyword can't be used for COMMUNITY
     value.  When `exact-match' is specified, it display only routes
     that have an exact match.

 - Command: show ip bgp community-list WORD
 - Command: show ip bgp community-list WORD exact-match
     This commands display BGP routes that matches community list WORD.
     When `exact-match' is specified, display only routes that have an
     exact match.


File: zebra.info,  Node: Using BGP Communities Attribute,  Prev: Display BGP Routes by Community,  Up: BGP Communities Attribute

Using BGP Communities Attribute
-------------------------------

   Following configuration is the most typical usage of BGP communities
attribute.  AS 7675 provides upstream Internet connection to AS 100.
When following configuration exists in AS 7675, AS 100 networks
operator can set local preference in AS 7675 network by setting BGP
communities attribute to the updates.

     router bgp 7675
      neighbor 192.168.0.1 remote-as 100
      neighbor 192.168.0.1 route-map RMAP in
     !
     ip community-list 70 permit 7675:70
     ip community-list 70 deny
     ip community-list 80 permit 7675:80
     ip community-list 80 deny
     ip community-list 90 permit 7675:90
     ip community-list 90 deny
     !
     route-map RMAP permit 10
      match community 70
      set local-preference 70
     !
     route-map RMAP permit 20
      match community 80
      set local-preference 80
     !
     route-map RMAP permit 30
      match community 90
      set local-preference 90

   Following configuration announce 10.0.0.0/8 from AS 100 to AS 7675.
The route has communities value 7675:80 so when above configuration
exists in AS 7675, announced route's local preference will be set to
value 80.

     router bgp 100
      network 10.0.0.0/8
      neighbor 192.168.0.2 remote-as 7675
      neighbor 192.168.0.2 route-map RMAP out
     !
     ip prefix-list PLIST permit 10.0.0.0/8
     !
     route-map RMAP permit 10
      match ip address prefix-list PLIST
      set community 7675:80

   Following configuration is an example of BGP route filtering using
communities attribute.  This configuration only permit BGP routes which
has BGP communities value 0:80 or 0:90.  Network operator can put
special internal communities value at BGP border router, then limit the
BGP routes announcement into the internal network.

     router bgp 7675
      neighbor 192.168.0.1 remote-as 100
      neighbor 192.168.0.1 route-map RMAP in
     !
     ip community-list 1 permit 0:80 0:90
     !
     route-map RMAP permit in
      match community 1

   Following exmaple filter BGP routes which has communities value 1:1.
When there is no match community-list returns deny.  To avoid filtering
all of routes, we need to define permit any at last.

     router bgp 7675
      neighbor 192.168.0.1 remote-as 100
      neighbor 192.168.0.1 route-map RMAP in
     !
     ip community-list standard FILTER deny 1:1
     ip community-list standard FILTER permit
     !
     route-map RMAP permit 10
      match community FILTER

   Communities value keyword `internet' has special meanings in
standard community lists.  In below example `internet' act as match
any.  It matches all of BGP routes even if the route does not have
communities attribute at all.  So community list `INTERNET' is same as
above example's `FILTER'.

     ip community-list standard INTERNET deny 1:1
     ip community-list standard INTERNET permit internet

   Following configuration is an example of communities value deletion.
With this configuration communities value 100:1 and 100:2 is removed
from BGP updates.  For communities value deletion, only `permit'
community-list is used.  `deny' community-list is ignored.

     router bgp 7675
      neighbor 192.168.0.1 remote-as 100
      neighbor 192.168.0.1 route-map RMAP in
     !
     ip community-list standard DEL permit 100:1 100:2
     !
     route-map RMAP permit 10
      set comm-list DEL delete


File: zebra.info,  Node: BGP Extended Communities Attribute,  Next: Displaying BGP routes,  Prev: BGP Communities Attribute,  Up: BGP

BGP Extended Communities Attribute
==================================

   MPLS VPN/BGP provides VPN functionality by using MPLS network and
BGP protocol support.  MPLS VPN/BGP expands capability of network
infrastructure.  At the same time, it requires a new framework for
policy routing.  BGP Extended Communities Attribute is introduced for
that.  With BGP Extended Communities Attribute we can use Route Target
or Site of Origin for implementing policy routing.

   BGP Extended Communities Attribute is similar to BGP Communities
Attribute.  It is an optional transitive attribute.  BGP Extended
Communities Attribute can carry multiple Extended Community value.
Each Extended Community value is eight octet length.

   BGP Extended Communities Attribute provides an extended range
compared with BGP Communities Attribute.  Adding to that there is a
type field in each value to provides community space structure.

   There are two format to define Extended Community value.  One is AS
based format the other is IP address based format.

`AS:VAL'
     This is a format to define AS based Extended Community value.
     `AS' part is 2 octets Global Administrator subfield in Extended
     Community value.  `VAL' part is 4 octets Local Administrator
     subfield.  `7675:100' represents AS 7675 policy value 100.

`IP-Address:VAL'
     This is a format to define IP address based Extended Community
     value.  `IP-Address' part is 4 octets Global Administrator
     subfield.  `VAL' part is 2 octets Local Administrator subfield.
     `10.0.0.1:100' represents

* Menu:

* BGP Extended Community Lists::
* BGP Extended Communities in Route Map::


File: zebra.info,  Node: BGP Extended Community Lists,  Next: BGP Extended Communities in Route Map,  Prev: BGP Extended Communities Attribute,  Up: BGP Extended Communities Attribute

BGP Extended Community Lists
----------------------------

   Expanded Community Lists is a user defined BGP Expanded Community
Lists.

 - Command: ip extcommunity-list standard NAME {permit|deny}
EXTCOMMUNITY
     This command defines a new standard extcommunity-list.
     EXTCOMMUNITY is extended communities value.  The EXTCOMMUNITY is
     compiled into extended community structure.  We can define
     multiple extcommunity-list under same name.  In that case match
     will happen user defined order.  Once the extcommunity-list
     matches to extended communities attribute in BGP updates it return
     permit or deny based upon the extcommunity-list definition.  When
     there is no matched entry, deny will be returned.  When
     EXTCOMMUNITY is empty it matches to any routes.

 - Command: ip extcommunity-list expanded NAME {permit|deny} LINE
     This command defines a new expanded extcommunity-list.  LINE is a
     string expression of extended communities attribute.  LINE can
     include regular expression to match extended communities attribute
     in BGP updates.

 - Command: no ip extcommunity-list NAME
 - Command: no ip extcommunity-list standard NAME
 - Command: no ip extcommunity-list expanded NAME
     These commands delete extended community lists specified by NAME.
     All of extended community lists shares a single name space.  So
     extended community lists can be removed simpley specifying the
     name.

 - Command: show ip extcommunity-list
 - Command: show ip extcommunity-list NAME
     This command display current extcommunity-list information.  When
     NAME is specified the community list's information is shown.

          # show ip extcommunity-list


File: zebra.info,  Node: BGP Extended Communities in Route Map,  Prev: BGP Extended Community Lists,  Up: BGP Extended Communities Attribute

BGP Extended Communities in Route Map
-------------------------------------

 - Route Map: match extcommunity WORD

 - Route Map: set extcommunity rt EXTCOMMUNITY
     This command set Route Target value.

 - Route Map: set extcommunity soo EXTCOMMUNITY
     This command set Site of Origin value.


File: zebra.info,  Node: Displaying BGP routes,  Next: Capability Negotiation,  Prev: BGP Extended Communities Attribute,  Up: BGP

Displaying BGP Routes
=====================

* Menu:

* Show IP BGP::
* More Show IP BGP::


File: zebra.info,  Node: Show IP BGP,  Next: More Show IP BGP,  Prev: Displaying BGP routes,  Up: Displaying BGP routes

Show IP BGP
-----------

 - Command: show ip bgp
 - Command: show ip bgp A.B.C.D
 - Command: show ip bgp X:X::X:X
     This command displays BGP routes.  When no route is specified it
     display all of IPv4 BGP routes.

     BGP table version is 0, local router ID is 10.1.1.1
     Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
     Origin codes: i - IGP, e - EGP, ? - incomplete
     
        Network          Next Hop            Metric LocPrf Weight Path
     *> 1.1.1.1/32       0.0.0.0                  0         32768 i
     
     Total number of prefixes 1


File: zebra.info,  Node: More Show IP BGP,  Prev: Show IP BGP,  Up: Displaying BGP routes

More Show IP BGP
----------------

 - Command: show ip bgp regexp LINE
     This command display BGP routes using AS path regular expression
     (*note Display BGP Routes by AS Path::).

 - Command: show ip bgp community COMMUNITY
 - Command: show ip bgp community COMMUNITY exact-match
     This command display BGP routes using COMMUNITY (*note Display BGP
     Routes by Community::).

 - Command: show ip bgp community-list WORD
 - Command: show ip bgp community-list WORD exact-match
     This command display BGP routes using community list (*note
     Display BGP Routes by Community::).

 - Command: show ip bgp summary

 - Command: show ip bgp neighbor [PEER]

 - Command: clear ip bgp PEER
     Clear peers which have addresses of X.X.X.X

 - Command: clear ip bgp PEER soft in
     Clear peer using soft reconfiguration.

 - Command: show debug

 - Command: debug event

 - Command: debug update

 - Command: debug keepalive

 - Command: no debug event

 - Command: no debug update

 - Command: no debug keepalive


File: zebra.info,  Node: Capability Negotiation,  Next: Route Reflector,  Prev: Displaying BGP routes,  Up: BGP

Capability Negotiation
======================

   When adding IPv6 routing information exchange feature to BGP.  There
were some proposals.  IETF IDR working group finally take a proposal
called Multiprotocol Extension for BGP.  The specification is described
in RFC2283.  The protocol does not define new protocols.  It defines
new attributes to existing BGP.  When it is used exchanging IPv6
routing information it is called BGP-4+.  When it is used for
exchanging multicast routing information it is called MBGP.

   `bgpd' supports Multiprotocol Extension for BGP.  So if remote peer
supports the protocol, `bgpd' can exchange IPv6 and/or multicast routing
information.

   Traditional BGP does not have the feature to detect remote peer's
capability whether it can handle other than IPv4 unicast routes.  This
is a big problem using Multiprotocol Extension for BGP to operational
network.  `draft-ietf-idr-bgp4-cap-neg-04.txt' is proposing a feature
called Capability Negotiation.  `bgpd' use this Capability Negotiation
to detect remote peer's capabilities.  If the peer is only configured
as IPv4 unicast neighbor, `bgpd' does not send these Capability
Negotiation packets.

   By default, Zebra will bring up peering with minimal common
capability for the both sides.  For example, local router has unicast
and multicast capabilitie and remote router has unicast capability.  In
this case, the local router will establish the connection with unicast
only capability.  When there are no common capabilities, Zebra sends
Unsupported Capability error and then resets the connection.

   If you want to completely match capabilities with remote peer.
Please use `strict-capability-match' command.

 - BGP: neighbor PEER strict-capability-match
 - BGP: no neighbor PEER strict-capability-match
     Strictly compares remote capabilities and local capabilities.  If
     capabilities are different, send Unsupported Capability error then
     reset connection.

   You may want to disable sending Capability Negotiation OPEN message
optional parameter to the peer when remote peer does not implement
Capability Negotiation.  Please use `dont-capability-negotiate' command
to disable the feature.

 - BGP: neighbor PEER dont-capability-negotiate
 - BGP: no neighbor PEER dont-capability-negotiate
     Suppress sending Capability Negotiation as OPEN message optional
     parameter to the peer.  This command only affects the peer is
     configured other than IPv4 unicast configuration.

   When remote peer does not have capability negotiation feature, remote
peer will not send any capabilities at all.  In that case, bgp
configures the peer with configured capabilities.

   You may prefer locally configured capabilities more than the
negotiated capabilities even though remote peer sends capabilities.  If
the peer is configured by `override-capability', `bgpd' ignores received
capabilities then override negotiated capabilities with configured
values.

 - BGP: neighbor PEER override-capability
 - BGP: no neighbor PEER override-capability
     Override the result of Capability Negotiation with local
     configuration.  Ignore remote peer's capability value.


File: zebra.info,  Node: Route Reflector,  Next: Route Server,  Prev: Capability Negotiation,  Up: BGP

Route Reflector
===============

 - BGP: bgp cluster-id A.B.C.D

 - BGP: neighbor PEER route-reflector-client
 - BGP: no neighbor PEER route-reflector-client


File: zebra.info,  Node: Route Server,  Next: How to set up a 6-Bone connection,  Prev: Route Reflector,  Up: BGP

Route Server
============

   At an Internet Exchange point, many ISPs are connected to each other
by external BGP peering.  Normally these external BGP connection are
done by `full mesh' method.  As with internal BGP full mesh formation,
this method has a scaling problem.

   This scaling problem is well known.  Route Server is a method to
resolve the problem.  Each ISP's BGP router only peers to Route Server.
Route Server serves as BGP information exchange to other BGP routers.
By applying this method, numbers of BGP connections is reduced from
O(n*(n-1)/2) to O(n).

   Unlike normal BGP router, Route Server must have several routing
tables for managing different routing policies for each BGP speaker.
We call the routing tables as different `view's.  `bgpd' can work as
normal BGP router or Route Server or both at the same time.

* Menu:

* Multiple instance::
* BGP instance and view::
* Routing policy::
* Viewing the view::


File: zebra.info,  Node: Multiple instance,  Next: BGP instance and view,  Prev: Route Server,  Up: Route Server

Multiple instance
-----------------

   To enable multiple view function of `bgpd', you must turn on
multiple instance feature beforehand.

 - Command: bgp multiple-instance
     Enable BGP multiple instance feature.  After this feature is
     enabled, you can make multiple BGP instances or multiple BGP views.

 - Command: no bgp multiple-instance
     Disable BGP multiple instance feature.  You can not disable this
     feature when BGP multiple instances or views exist.

   When you want to make configuration more Cisco like one,

 - Command: bgp config-type cisco
     Cisco compatible BGP configuration output.

   When bgp config-type cisco is specified,

   "no synchronization" is displayed.  "no auto-summary" is desplayed.

   "network" and "aggregate-address" argument is displayed as "A.B.C.D
M.M.M.M"

   Zebra: network 10.0.0.0/8 Cisco: network 10.0.0.0

   Zebra: aggregate-address 192.168.0.0/24 Cisco: aggregate-address
192.168.0.0 255.255.255.0

   Community attribute handling is also different.  If there is no
configuration is specified community attribute and extended community
attribute are sent to neighbor.  When user manually disable the feature
community attribute is not sent to the neighbor.  In case of "bgp
config-type cisco" is specified, community attribute is not sent to the
neighbor by default.  To send community attribute user has to specify
"neighbor A.B.C.D send-community" command.

   !  router bgp 1  neighbor 10.0.0.1 remote-as 1  no neighbor 10.0.0.1
send-community !

   !  router bgp 1  neighbor 10.0.0.1 remote-as 1  neighbor 10.0.0.1
send-community !

 - Command: bgp config-type zebra
     Zebra style BGP configuration.  This is default.


File: zebra.info,  Node: BGP instance and view,  Next: Routing policy,  Prev: Multiple instance,  Up: Route Server

BGP instance and view
---------------------

   BGP instance is a normal BGP process.  The result of route selection
goes to the kernel routing table.  You can setup different AS at the
same time when BGP multiple instance feature is enabled.

 - Command: router bgp AS-NUMBER
     Make a new BGP instance.  You can use arbitrary word for the NAME.

     bgp multiple-instance
     !
     router bgp 1
      neighbor 10.0.0.1 remote-as 2
      neighbor 10.0.0.2 remote-as 3
     !
     router bgp 2
      neighbor 10.0.0.3 remote-as 4
      neighbor 10.0.0.4 remote-as 5

   BGP view is almost same as normal BGP process. The result of route
selection does not go to the kernel routing table.  BGP view is only
for exchanging BGP routing information.

 - Command: router bgp AS-NUMBER view NAME
     Make a new BGP view.  You can use arbitrary word for the NAME.
     This view's route selection result does not go to the kernel
     routing table.

   With this command, you can setup Route Server like below.

     bgp multiple-instance
     !
     router bgp 1 view 1
      neighbor 10.0.0.1 remote-as 2
      neighbor 10.0.0.2 remote-as 3
     !
     router bgp 2 view 2
      neighbor 10.0.0.3 remote-as 4
      neighbor 10.0.0.4 remote-as 5


File: zebra.info,  Node: Routing policy,  Next: Viewing the view,  Prev: BGP instance and view,  Up: Route Server

Routing policy
--------------

   You can set different routing policy for a peer.  For example, you
can set different filter for a peer.

     bgp multiple-instance
     !
     router bgp 1 view 1
      neighbor 10.0.0.1 remote-as 2
      neighbor 10.0.0.1 distribute-list 1 in
     !
     router bgp 1 view 2
      neighbor 10.0.0.1 remote-as 2
      neighbor 10.0.0.1 distribute-list 2 in

   This means BGP update from a peer 10.0.0.1 goes to both BGP view 1
and view 2.  When the update is inserted into view 1, distribute-list 1
is applied.  On the other hand, when the update is inserted into view 2,
distribute-list 2 is applied.


File: zebra.info,  Node: Viewing the view,  Prev: Routing policy,  Up: Route Server

Viewing the view
----------------

   To display routing table of BGP view, you must specify view name.

 - Command: show ip bgp view NAME
     Display routing table of BGP view NAME.


File: zebra.info,  Node: How to set up a 6-Bone connection,  Next: Dump BGP packets and table,  Prev: Route Server,  Up: BGP

How to set up a 6-Bone connection
=================================

     zebra configuration
     ===================
     !
     ! Actually there is no need to configure zebra
     !
     
     bgpd configuration
     ==================
     !
     ! This means that routes go through zebra and into the kernel.
     !
     router zebra
     !
     ! MP-BGP configuration
     !
     router bgp 7675
      bgp router-id 10.0.0.1
      neighbor 3ffe:1cfa:0:2:2a0:c9ff:fe9e:f56 remote-as AS-NUMBER
     !
      address-family ipv6
      network 3ffe:506::/32
      neighbor 3ffe:1cfa:0:2:2a0:c9ff:fe9e:f56 activate
      neighbor 3ffe:1cfa:0:2:2a0:c9ff:fe9e:f56 route-map set-nexthop out
      neighbor 3ffe:1cfa:0:2:2c0:4fff:fe68:a231 remote-as AS-NUMBER
      neighbor 3ffe:1cfa:0:2:2c0:4fff:fe68:a231 route-map set-nexthop out
      exit-address-family
     !
     ipv6 access-list all permit any
     !
     ! Set output nexthop address.
     !
     route-map set-nexthop permit 10
      match ipv6 address all
      set ipv6 nexthop global 3ffe:1cfa:0:2:2c0:4fff:fe68:a225
      set ipv6 nexthop local fe80::2c0:4fff:fe68:a225
     !
     ! logfile FILENAME is obsolete.  Please use log file FILENAME
     !
     log file bgpd.log
     !


File: zebra.info,  Node: Dump BGP packets and table,  Prev: How to set up a 6-Bone connection,  Up: BGP

Dump BGP packets and table
==========================

 - Command: dump bgp all PATH
 - Command: dump bgp all PATH INTERVAL
     Dump all BGP packet and events to PATH file.

 - Command: dump bgp updates PATH
 - Command: dump bgp updates PATH INTERVAL
     Dump BGP updates to PATH file.

 - Command: dump bgp routes PATH
 - Command: dump bgp routes PATH
     Dump whole BGP routing table to PATH.  This is heavy process.


File: zebra.info,  Node: VTY shell,  Next: Filtering,  Prev: BGP,  Up: Top

VTY shell
*********

   `vtysh' is integrated shell of Zebra software.

   To use vtysh please specify --enable-vtysh to configure script.  To
use PAM for authentication use --with-libpam option to configure script.

   vtysh only searches /usr/local/etc path for vtysh.conf which is the
vtysh configuration file.  Vtysh does not search current directory for
configuration file because the file includes user authentication
settings.

   Currently, vtysh.conf has only one command.

     !
     username foo nopassword
     !

   With this set, user foo does not need password authentication for
user vtysh.  With PAM vtysh uses PAM authentication mechanism.

   If vtysh is compiled without PAM authentication, every user can use
vtysh without authentication.


File: zebra.info,  Node: Filtering,  Next: Route Map,  Prev: VTY shell,  Up: Top

Filtering
*********

   Zebra provides many very flexible filtering features.  Filtering is
used for both input and output of the routing information.  Once
filtering is defined, it can be applied in any direction.

* Menu:

* IP Access List::
* IP Prefix List::


File: zebra.info,  Node: IP Access List,  Next: IP Prefix List,  Prev: Filtering,  Up: Filtering

IP Access List
--------------

 - Command: access-list NAME permit IPV4-NETWORK
 - Command: access-list NAME deny IPV4-NETWORK

   Basic filtering is done by `access-list' as shown in the following
example.

     access-list filter deny 10.0.0.0/9
     access-list filter permit 10.0.0.0/8


File: zebra.info,  Node: IP Prefix List,  Prev: IP Access List,  Up: Filtering

IP Prefix List
--------------

   `ip prefix-list' provides the most powerful prefix based filtering
mechanism.  In addition to `access-list' functionality, `ip
prefix-list' has prefix length range specification and sequential
number specification.  You can add or delete prefix based filters to
arbitrary points of prefix-list using sequential number specification.

   If no ip prefix-list is specified, it acts as permit.  If `ip
prefix-list' is defined, and no match is found, default deny is applied.

 - Command: ip prefix-list NAME (permit|deny) PREFIX [le LEN] [ge LEN]
 - Command: ip prefix-list NAME seq NUMBER (permit|deny) PREFIX [le
LEN] [ge LEN]
     You can create `ip prefix-list' using above commands.

    seq
          seq NUMBER can be set either automatically or manually.  In
          the case that sequential numbers are set manually, the user
          may pick any number less than 4294967295.  In the case that
          sequential number are set automatically, the sequential
          number will increase by a unit of five (5) per list.  If a
          list with no specified sequential number is created after a
          list with a specified sequential number, the list will
          automatically pick the next multiple of five (5) as the list
          number.  For example, if a list with number 2 already exists
          and a new list with no specified number is created, the next
          list will be numbered 5.  If lists 2 and 7 already exist and
          a new list with no specified number is created, the new list
          will be numbered 10.

    le
          `le' command specifies prefix length.  The prefix list will be
          applied if the prefix length is less than or equal to the le
          prefix length.

    ge
          `ge' command specifies prefix length.  The prefix list will be
          applied if the prefix length is greater than or equal to the
          ge prefix length.


   Less than or equal to prefix numbers and greater than or equal to
prefix numbers can be used together.  The order of the le and ge
commands does not matter.

   If a prefix list with a different sequential number but with the
exact same rules as a previous list is created, an error will result.
However, in the case that the sequential number and the rules are
exactly similar, no error will result.

   If a list with the same sequential number as a previous list is
created, the new list will overwrite the old list.

   Matching of IP Prefix is performed from the smaller sequential
number to the larger.  The matching will stop once any rule has been
applied.

   In the case of no le or ge command,

   Version 0.85: the matching rule will apply to all prefix lengths that
matched the prefix list.

   Version 0.86 or later: In the case of no le or ge command, the prefix
length must match exactly the length specified in the prefix list.

 - Command: no ip prefix-list NAME

* Menu:

* ip prefix-list description::
* ip prefix-list sequential number control::
* Showing ip prefix-list::
* Clear counter of ip prefix-list::


File: zebra.info,  Node: ip prefix-list description,  Next: ip prefix-list sequential number control,  Prev: IP Prefix List,  Up: IP Prefix List

ip prefix-list description
..........................

 - Command: ip prefix-list NAME description DESC
     Descriptions may be added to prefix lists.  This command adds a
     description to the prefix list.

 - Command: no ip prefix-list NAME description [DESC]
     Deletes the description from a prefix list.  It is possible to use
     the command without the full description.


File: zebra.info,  Node: ip prefix-list sequential number control,  Next: Showing ip prefix-list,  Prev: ip prefix-list description,  Up: IP Prefix List

ip prefix-list sequential number control
........................................

 - Command: ip prefix-list sequence-number
     With this command, the IP prefix list sequential number is
     displayed.  This is the default behavior.

 - Command: no ip prefix-list sequence-number
     With this command, the IP prefix list sequential number is not
     displayed.


File: zebra.info,  Node: Showing ip prefix-list,  Next: Clear counter of ip prefix-list,  Prev: ip prefix-list sequential number control,  Up: IP Prefix List

Showing ip prefix-list
......................

 - Command: show ip prefix-list
     Display all IP prefix lists.

 - Command: show ip prefix-list NAME
     Show IP prefix list can be used with a prefix list name.

 - Command: show ip prefix-list NAME seq NUM
     Show IP prefix list can be used with a prefix list name and
     sequential number.

 - Command: show ip prefix-list NAME A.B.C.D/M
     If the command longer is used, all prefix lists with prefix
     lengths equal to or longer than the specified length will be
     displayed.  If the command first match is used, the first prefix
     length match will be displayed.

 - Command: show ip prefix-list NAME A.B.C.D/M longer

 - Command: show ip prefix-list NAME A.B.C.D/M first-match

 - Command: show ip prefix-list summary

 - Command: show ip prefix-list summary NAME

 - Command: show ip prefix-list detail

 - Command: show ip prefix-list detail NAME


File: zebra.info,  Node: Clear counter of ip prefix-list,  Prev: Showing ip prefix-list,  Up: IP Prefix List

Clear counter of ip prefix-list
...............................

 - Command: clear ip prefix-list
     Clears the counters of all IP prefix lists.  Clear IP Prefix List
     can be used with a specified name and prefix.

 - Command: clear ip prefix-list NAME

 - Command: clear ip prefix-list NAME A.B.C.D/M


File: zebra.info,  Node: Route Map,  Next: IPv6 Support,  Prev: Filtering,  Up: Top

Route Map
*********

   Route map is a very useful function in zebra.  There is a match and
set statement permitted in a route map.

     route-map test permit 10
      match ip address 10
      set local-preference 200

   This means that if a route matches ip access-list number 10 it's
local-preference value is set to 200.

* Menu:

* Route Map Command::
* Route Map Match Command::
* Route Map Set Command::


File: zebra.info,  Node: Route Map Command,  Next: Route Map Match Command,  Prev: Route Map,  Up: Route Map

Route Map Command
-----------------

 - Command: route-map ROUTE-MAP-NAME permit PRIORITY


File: zebra.info,  Node: Route Map Match Command,  Next: Route Map Set Command,  Prev: Route Map Command,  Up: Route Map

Route Map Match Command
-----------------------

 - Route-map Command: match ip address ACCESS_LIST
     Matches the specified ACCESS_LIST

 - Route-map Command: match ip next-hop IPV4_ADDR
     Matches the specified IPV4_ADDR.

 - Route-map Command: match aspath AS_PATH
     Matches the specified AS_PATH.

 - Route-map Command: match metric METRIC
     Matches the specified METRIC.

 - Route-map Command: match community COMMUNITY_LIST
     Matches the specified  COMMUNITY_LIST


File: zebra.info,  Node: Route Map Set Command,  Prev: Route Map Match Command,  Up: Route Map

Route Map Set Command
---------------------

 - Route-map Command: set ip next-hop IPV4_ADDRESS
     Set the BGP nexthop address.

 - Route-map Command: set local-preference LOCAL_PREF
     Set the BGP local preference.

 - Route-map Command: set weight WEIGHT
     Set the route's weight.

 - Route-map Command: set metric METRIC
     Set the BGP attribute MED.

 - Route-map Command: set as-path prepend AS_PATH
     Set the BGP AS path to prepend.

 - Route-map Command: set community COMMUNITY
     Set the BGP community attribute.

 - Route-map Command: set ipv6 next-hop global IPV6_ADDRESS
     Set the BGP-4+ global IPv6 nexthop address.

 - Route-map Command: set ipv6 next-hop local IPV6_ADDRESS
     Set the BGP-4+ link local IPv6 nexthop address.


File: zebra.info,  Node: IPv6 Support,  Next: Kernel Interface,  Prev: Route Map,  Up: Top

IPv6 Support
************

   Zebra fully supports IPv6 routing.  As described so far, Zebra
supports RIPng, OSPFv3 and BGP-4+.  You can give IPv6 addresses to an
interface and configure static IPv6 routing information.  Zebra-IPv6
also provides automatic address configuration via a feature called
`address auto configuration'.  To do it, the router must send router
advertisement messages to the all nodes that exist on the network.

* Menu:

* Router Advertisement::


File: zebra.info,  Node: Router Advertisement,  Prev: IPv6 Support,  Up: IPv6 Support

Router Advertisement
====================

 - Interface Command: ipv6 nd send-ra

 - Interface Command: ipv6 nd prefix-advertisement IPV6PREFIX

     interface eth0
      ipv6 nd send-ra
      ipv6 nd prefix-advertisement 3ffe:506:5009::/64


File: zebra.info,  Node: Kernel Interface,  Next: SNMP Support,  Prev: IPv6 Support,  Up: Top

Kernel Interface
****************

   There are several different methods for reading kernel routing table
information, updating kernel routing tables, and for looking up
interfaces.

`ioctl'
     The `ioctl' method is a very traditional way for reading or writing
     kernel information.  `ioctl' can be used for looking up interfaces
     and for modifying interface addresses, flags, mtu settings and
     other types of information.  Also, `ioctl' can insert and delete
     kernel routing table entries.  It will soon be available on almost
     any platform which zebra supports, but it is a little bit ugly
     thus far, so if a better method is supported by the kernel, zebra
     will use that.

`sysctl'
     `sysctl' can lookup kernel information using MIB (Management
     Information Base) syntax.  Normally, it only provides a way of
     getting information from the kernel.  So one would usually want to
     change kernel information using another method such as `ioctl'.

`proc filesystem'
     `proc filesystem' provides an easy way of getting kernel
     information.

`routing socket'

`netlink'
     On recent Linux kernels (2.0.x and 2.2.x), there is a kernel/user
     communication support called `netlink'.  It makes asynchronous
     communication between kernel and Zebra possible, similar to a
     routing socket on BSD systems.

     Before you use this feature, be sure to select (in kernel
     configuration) the kernel/netlink support option 'Kernel/User
     network link driver' and 'Routing messages'.

     Today, the /dev/route special device file is obsolete.  Netlink
     communication is done by reading/writing over netlink socket.

     After the kernel configuration, please reconfigure and rebuild
     Zebra.  You can use netlink as a dynamic routing update channel
     between Zebra and the kernel.


File: zebra.info,  Node: SNMP Support,  Next: Zebra Protocol,  Prev: Kernel Interface,  Up: Top

SNMP Support
************

   SNMP (Simple Network Managing Protocol) is widely implemented feature
for collecting network information from router and/or host.  Zebra
itself does not support SNMP agent functionality.  But conjuction with
SNMP agent, Zebra provides routing protocol MIBs.

   Zebra uses SMUX protocol (RFC1227) for making communication with SNMP
agent.  There are several SNMP agent which support SMUX.  We recommend
to use the latest `ucd-snmp' software.

* Menu:

* How to get ucd-snmp::
* SMUX configuration::


File: zebra.info,  Node: How to get ucd-snmp,  Next: SMUX configuration,  Prev: SNMP Support,  Up: SNMP Support

How to get ucd-snmp
===================

   ucd-snmp is a free software which distributed so called "as is"
software license.  Please check the license which comes with
distribution of `ucd-snmp'.  The authors of ucd-snmp are the University
of California, the University of California at Davis, and the Electrical
Engineering department at the University of California at Davis.

   You can get ucd-snmp from <ftp://ucd-snmp.ucdavis.edu/>.  As of this
writing we are testing with `ucd-snmp-4.1.pre1.tar.gz'.

   To enable SMUX protocol support, please configure `ucd-snmp' like
below.

     % configure --with-mib-modules=smux

   After compile and install `ucd-snmp', you will need to configure
smuxpeer.  I'm now using configuration shown below.  This means SMUX
client connects to MIB 1.3.6.1.6.3.1 with password test.

     /usr/local/share/snmp/snmpd.conf
     ================================
     smuxpeer 1.3.6.1.6.3.1 test


File: zebra.info,  Node: SMUX configuration,  Prev: How to get ucd-snmp,  Up: SNMP Support

SMUX configuration
==================

   To enable SNMP support of Zebra, you have to configure Zebra with
`--enable-snmp' (*note Configure the Software::).

 - Command: smux peer OID
 - Command: no smux peer OID

 - Command: smux peer OID PASSWORD
 - Command: no smux peer OID PASSWORD

     !
     smux peer .1.3.6.1.6.3.1 test
     !


File: zebra.info,  Node: Zebra Protocol,  Next: Packet Binary Dump Format,  Prev: SNMP Support,  Up: Top

Zebra Protocol
**************

   Zebra Protocol is a protocol which is used between protocol daemon
and zebra.  Each protocol daemon sends selected routes to zebra daemon.
Then zebra manages which route is installed into the forwarding table.

   Zebra Protocol is a TCP-based protocol.  Below is common header of
Zebra Protocol.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |           Length (2)          |   Command (1) |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Length is total packet length including this header length.  So
minimum length is three.  Command is Zebra Protocol command.

     ZEBRA_INTERFACE_ADD                1
     ZEBRA_INTERFACE_DELETE             2
     ZEBRA_INTERFACE_ADDRESS_ADD        3
     ZEBRA_INTERFACE_ADDRESS_DELETE     4
     ZEBRA_INTERFACE_UP                 5
     ZEBRA_INTERFACE_DOWN               6
     ZEBRA_IPV4_ROUTE_ADD               7
     ZEBRA_IPV4_ROUTE_DELETE            8
     ZEBRA_IPV6_ROUTE_ADD               9
     ZEBRA_IPV6_ROUTE_DELETE           10
     ZEBRA_REDISTRIBUTE_ADD            11
     ZEBRA_REDISTRIBUTE_DELETE         12
     ZEBRA_REDISTRIBUTE_DEFAULT_ADD    13
     ZEBRA_REDISTRIBUTE_DEFAULT_DELETE 14
     ZEBRA_IPV4_NEXTHOP_LOOKUP         15
     ZEBRA_IPV6_NEXTHOP_LOOKUP         16

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |             Type              |             Flags             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


File: zebra.info,  Node: Packet Binary Dump Format,  Prev: Zebra Protocol,  Up: Top

Packet Binary Dump Format
*************************

   Zebra can dump routing protocol packet into file with a binary format
(*note Dump BGP packets and table::).

   It seems to be better that we share the MRT's header format for
backward compatibility with MRT's dump logs. We should also define the
binary format excluding the header, because we must support both IP v4
and v6 addresses as socket addresses and / or routing entries.

   In the last meeting, we discussed to have a version field in the
header. But Masaki told us that we can define new `type' value rather
than having a `version' field, and it seems to be better because we
don't need to change header format.

   Here is the common header format. This is same as that of MRT.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                              Time                             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |             Type              |            Subtype            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                             Length                            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   If `type' is PROTOCOL_BGP4MP, `subtype' is BGP4MP_STATE_CHANGE, and
Address Family == IP (version 4)

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Source AS number       |     Destination AS number     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Interface Index        |      Address Family           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            Old State          |           New State           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Where State is the value defined in RFC1771.

   If `type' is PROTOCOL_BGP4MP, `subtype' is BGP4MP_STATE_CHANGE, and
Address Family == IP version 6

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Source AS number       |     Destination AS number     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Interface Index        |      Address Family           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address (Cont'd)             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address (Cont'd)             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address (Cont'd)             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address (Cont'd)           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address (Cont'd)           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address (Cont'd)           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            Old State          |           New State           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   If `type' is PROTOCOL_BGP4MP, `subtype' is BGP4MP_MESSAGE, and
Address Family == IP (version 4)

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Source AS number       |     Destination AS number     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Interface Index        |      Address Family           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       BGP Message Packet                      |
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Where BGP Message Packet is the whole contents of the BGP4 message
including header portion.

   If `type' is PROTOCOL_BGP4MP, `subtype' is BGP4MP_MESSAGE, and
Address Family == IP version 6

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Source AS number       |     Destination AS number     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |        Interface Index        |      Address Family           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address (Cont'd)             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address (Cont'd)             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Source IP address (Cont'd)             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address (Cont'd)           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address (Cont'd)           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Destination IP address (Cont'd)           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       BGP Message Packet                      |
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   If `type' is PROTOCOL_BGP4MP, `subtype' is BGP4MP_ENTRY, and Address
Family == IP (version 4)

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            View #             |            Status             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Time Last Change                       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       Address Family          |    SAFI       | Next-Hop-Len  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Next Hop Address                       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Prefix Length |             Address Prefix [variable]         |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       Attribute Length        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |      BGP Attribute [variable length]    			|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   If `type' is PROTOCOL_BGP4MP, `subtype' is BGP4MP_ENTRY, and Address
Family == IP version 6

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            View #             |            Status             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Time Last Change                       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       Address Family          |    SAFI       | Next-Hop-Len  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Next Hop Address                       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Next Hop Address (Cont'd)              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Next Hop Address (Cont'd)              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                        Next Hop Address (Cont'd)              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     | Prefix Length |             Address Prefix [variable]         |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Address Prefix (cont'd) [variable]        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       Attribute Length        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |      BGP Attribute [variable length]    			    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   	BGP4 Attribute must not contain MP_UNREACH_NLRI.  	If BGP Attribute
has MP_REACH_NLRI field, it must has 	zero length NLRI, e.g.,
MP_REACH_NLRI has only Address 	Family, SAFI and next-hop values.

   If `type' is PROTOCOL_BGP4MP and `subtype' is BGP4MP_SNAPSHOT,

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |           View #              |       File Name [variable]    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The file specified in "File Name" contains all routing entries,
which are in the format of "subtype == BGP4MP_ENTRY".

     Constants:
       /* type value */
       #define MSG_PROTOCOL_BGP4MP 16
       /* subtype value */
       #define BGP4MP_STATE_CHANGE 0
       #define BGP4MP_MESSAGE 1
       #define BGP4MP_ENTRY 2
       #define BGP4MP_SNAPSHOT 3


File: zebra.info,  Node: Command Index,  Next: VTY Key Index,  Prev: Top,  Up: Top

Command Index
*************

* Menu:

* access-class ACCESS-LIST:              Basic Config Commands.
* access-list NAME deny IPV4-NETWORK:    IP Access List.
* access-list NAME permit IPV4-NETWORK:  IP Access List.
* aggregate-address A.B.C.D/M:           Route Aggregation.
* aggregate-address A.B.C.D/M as-set:    Route Aggregation.
* aggregate-address A.B.C.D/M summary-only: Route Aggregation.
* area <0-4294967295> authentication:    OSPF area.
* area <0-4294967295> authentication message-digest: OSPF area.
* area <0-4294967295> export-list NAME:  OSPF area.
* area <0-4294967295> import-list NAME:  OSPF area.
* area <0-4294967295> range A.B.C.D/M:   OSPF area.
* area <0-4294967295> shortcut:          OSPF area.
* area <0-4294967295> stub:              OSPF area.
* area <0-4294967295> stub no-summary:   OSPF area.
* area <0-4294967295> virtual-link A.B.C.D: OSPF area.
* area A.B.C.D authentication:           OSPF area.
* area A.B.C.D authentication message-digest: OSPF area.
* area A.B.C.D default-cost <0-16777215>: OSPF area.
* area A.B.C.D export-list NAME:         OSPF area.
* area A.B.C.D import-list NAME:         OSPF area.
* area A.B.C.D range A.B.C.D/M:          OSPF area.
* area A.B.C.D range IPV4_PREFIX substitute IPV4_PREFIX: OSPF area.
* area A.B.C.D range IPV4_PREFIX suppress: OSPF area.
* area A.B.C.D shortcut:                 OSPF area.
* area A.B.C.D stub:                     OSPF area.
* area A.B.C.D stub no-summary:          OSPF area.
* area A.B.C.D virtual-link A.B.C.D:     OSPF area.
* auto-cost refrence-bandwidth <1-4294967>: OSPF router.
* bandwidth <1-10000000>:                Interface Commands.
* banner motd default:                   Basic Config Commands.
* bgp cluster-id A.B.C.D:                Route Reflector.
* bgp config-type cisco:                 Multiple instance.
* bgp config-type zebra:                 Multiple instance.
* bgp multiple-instance:                 Multiple instance.
* bgp router-id A.B.C.D:                 BGP router.
* clear ip bgp PEER:                     More Show IP BGP.
* clear ip bgp PEER soft in:             More Show IP BGP.
* clear ip prefix-list:                  Clear counter of ip prefix-list.
* clear ip prefix-list NAME:             Clear counter of ip prefix-list.
* clear ip prefix-list NAME A.B.C.D/M:   Clear counter of ip prefix-list.
* configure terminal:                    Basic Config Commands.
* debug event:                           More Show IP BGP.
* debug keepalive:                       More Show IP BGP.
* debug ospf ism:                        Debugging OSPF.
* debug ospf ism (status|events|timers): Debugging OSPF.
* debug ospf lsa:                        Debugging OSPF.
* debug ospf lsa (generate|flooding|refresh): Debugging OSPF.
* debug ospf nsm:                        Debugging OSPF.
* debug ospf nsm (status|events|timers): Debugging OSPF.
* debug ospf packet (hello|dd|ls-request|ls-update|ls-ack|all) (send|recv) [detail]: Debugging OSPF.
* debug ospf zebra:                      Debugging OSPF.
* debug ospf zebra (interface|redistribute): Debugging OSPF.
* debug rip events:                      RIP Debug Commands.
* debug rip packet:                      RIP Debug Commands.
* debug rip zebra:                       RIP Debug Commands.
* debug ripng events:                    ripngd Terminal Mode Commands.
* debug ripng packet:                    ripngd Terminal Mode Commands.
* debug ripng zebra:                     ripngd Terminal Mode Commands.
* debug update:                          More Show IP BGP.
* default-information originate <1>:     How to Announce RIP route.
* default-information originate:         Redistribute routes to OSPF.
* default-information originate always:  Redistribute routes to OSPF.
* default-information originate always metric <0-16777214>: Redistribute routes to OSPF.
* default-information originate always metric <0-16777214> metric-type (1|2): Redistribute routes to OSPF.
* default-information originate always metric <0-16777214> metric-type (1|2) route-map WORD: Redistribute routes to OSPF.
* default-information originate metric <0-16777214>: Redistribute routes to OSPF.
* default-information originate metric <0-16777214> metric-type (1|2): Redistribute routes to OSPF.
* default-information originate metric <0-16777214> metric-type (1|2) route-map WORD: Redistribute routes to OSPF.
* default-metric <0-16777214>:           Redistribute routes to OSPF.
* default-metric <1-16>:                 RIP Metric Manipulation.
* description DESCRIPTION ...:           Interface Commands.
* distance <1-255> <1>:                  Redistribute routes to OSPF.
* distance <1-255>:                      RIP distance.
* distance <1-255> A.B.C.D/M <1>:        RIP distance.
* distance <1-255> A.B.C.D/M:            BGP distance.
* distance <1-255> A.B.C.D/M ACCESS-LIST: RIP distance.
* distance <1-255> A.B.C.D/M WORD:       BGP distance.
* distance bgp <1-255> <1-255> <1-255>:  BGP distance.
* distance ospf (intra-area|inter-area|external) <1-255>: Redistribute routes to OSPF.
* distribute-list ACCESS_LIST (in|out) IFNAME: ripngd Filtering Commands.
* distribute-list ACCESS_LIST DIRECT IFNAME: Filtering RIP Routes.
* distribute-list NAME out (kernel|connected|static|rip|ospf: Redistribute routes to OSPF.
* distribute-list prefix PREFIX_LIST (in|out) IFNAME: Filtering RIP Routes.
* dump bgp all PATH:                     Dump BGP packets and table.
* dump bgp all PATH INTERVAL:            Dump BGP packets and table.
* dump bgp routes PATH:                  Dump BGP packets and table.
* dump bgp updates PATH:                 Dump BGP packets and table.
* dump bgp updates PATH INTERVAL:        Dump BGP packets and table.
* enable password PASSWORD:              Basic Config Commands.
* exec-timeout MINUTE:                   Basic Config Commands.
* exec-timeout MINUTE SECOND:            Basic Config Commands.
* flush_timer TIME:                      ripngd Configuration.
* hostname HOSTNAME:                     Basic Config Commands.
* interface IFNAME:                      Interface Commands.
* interface IFNAME area AREA:            OSPF6 router.
* ip address ADDRESS:                    Interface Commands.
* ip as-path access-list WORD {permit|deny} LINE: AS Path Access List.
* ip community-list <1-99> {permit|deny} COMMUNITY: Numbered BGP Community Lists.
* ip community-list <100-199> {permit|deny} COMMUNITY: Numbered BGP Community Lists.
* ip community-list expanded NAME {permit|deny} LINE: BGP Community Lists.
* ip community-list NAME {permit|deny} COMMUNITY: Numbered BGP Community Lists.
* ip community-list standard NAME {permit|deny} COMMUNITY: BGP Community Lists.
* ip extcommunity-list expanded NAME {permit|deny} LINE: BGP Extended Community Lists.
* ip extcommunity-list standard NAME {permit|deny} EXTCOMMUNITY: BGP Extended Community Lists.
* ip ospf authentication-key AUTH_KEY:   OSPF interface.
* ip ospf cost <1-65535>:                OSPF interface.
* ip ospf dead-interval <1-65535>:       OSPF interface.
* ip ospf hello-interval <1-65535>:      OSPF interface.
* ip ospf message-digest-key KEYID md5 KEY: OSPF interface.
* ip ospf network (broadcast|non-broadcast|point-to-multipoint|point-to-point): OSPF interface.
* ip ospf priority <0-255>:              OSPF interface.
* ip ospf retransmit-interval <1-65535>: OSPF interface.
* ip ospf transmit-delay:                OSPF interface.
* ip prefix-list NAME (permit|deny) PREFIX [le LEN] [ge LEN]: IP Prefix List.
* ip prefix-list NAME description DESC:  ip prefix-list description.
* ip prefix-list NAME seq NUMBER (permit|deny) PREFIX [le LEN] [ge LEN]: IP Prefix List.
* ip prefix-list sequence-number:        ip prefix-list sequential number control.
* ip rip authentication key-chain KEY-CHAIN: RIP Authentication.
* ip rip authentication mode md5:        RIP Authentication.
* ip rip authentication mode text:       RIP Authentication.
* ip rip authentication string STRING:   RIP Authentication.
* ip rip receive version VERSION:        RIP Configuration.
* ip rip send version VERSION:           RIP Configuration.
* ip route NETWORK GATEWAY:              Static Route Commands.
* ip route NETWORK GATEWAY DISTANCE:     Static Route Commands.
* ip route NETWORK NETMASK GATEWAY:      Static Route Commands.
* ip split-horizon:                      RIP Configuration.
* ipv6 nd prefix-advertisement IPV6PREFIX: Router Advertisement.
* ipv6 nd send-ra:                       Router Advertisement.
* ipv6 ospf6 cost COST:                  OSPF6 interface.
* ipv6 ospf6 dead-interval DEADINTERVAL: OSPF6 interface.
* ipv6 ospf6 hello-interval HELLOINTERVAL: OSPF6 interface.
* ipv6 ospf6 priority PRIORITY:          OSPF6 interface.
* ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL: OSPF6 interface.
* ipv6 ospf6 transmit-delay TRANSMITDELAY: OSPF6 interface.
* ipv6 route NETWORK GATEWAY:            Static Route Commands.
* ipv6 route NETWORK GATEWAY DISTANCE:   Static Route Commands.
* line vty:                              Basic Config Commands.
* list:                                  Basic Config Commands.
* log file FILENAME:                     Basic Config Commands.
* log stdout:                            Basic Config Commands.
* log syslog:                            Basic Config Commands.
* match as-path WORD:                    Using AS Path in Route Map.
* match aspath AS_PATH:                  Route Map Match Command.
* match community COMMUNITY_LIST:        Route Map Match Command.
* match community WORD:                  BGP Community in Route Map.
* match community WORD exact-match:      BGP Community in Route Map.
* match extcommunity WORD:               BGP Extended Communities in Route Map.
* match interface WORD:                  RIP route-map.
* match ip address ACCESS_LIST:          Route Map Match Command.
* match ip address prefix-list WORD:     RIP route-map.
* match ip address WORD:                 RIP route-map.
* match ip next-hop A.B.C.D:             RIP route-map.
* match ip next-hop IPV4_ADDR:           Route Map Match Command.
* match metric <0-4294967295>:           RIP route-map.
* match metric METRIC:                   Route Map Match Command.
* multicast:                             Interface Commands.
* neighbor A.B.C.D:                      RIP Configuration.
* neighbor PEER default-originate:       BGP Peer commands.
* neighbor PEER description ...:         BGP Peer commands.
* neighbor PEER distribute-list NAME [in|out]: Peer filtering.
* neighbor PEER dont-capability-negotiate: Capability Negotiation.
* neighbor PEER ebgp-multihop:           BGP Peer commands.
* neighbor PEER filter-list NAME [in|out]: Peer filtering.
* neighbor PEER interface IFNAME:        BGP Peer commands.
* neighbor PEER maximum-prefix NUMBER:   BGP Peer commands.
* neighbor PEER next-hop-self:           BGP Peer commands.
* neighbor PEER override-capability:     Capability Negotiation.
* neighbor PEER peer-group WORD:         BGP Peer Group.
* neighbor PEER port PORT:               BGP Peer commands.
* neighbor PEER prefix-list NAME [in|out]: Peer filtering.
* neighbor PEER remote-as ASN:           Defining Peer.
* neighbor PEER route-map NAME [in|out]: Peer filtering.
* neighbor PEER route-reflector-client:  Route Reflector.
* neighbor PEER send-community:          BGP Peer commands.
* neighbor PEER shutdown:                BGP Peer commands.
* neighbor PEER strict-capability-match: Capability Negotiation.
* neighbor PEER update-source:           BGP Peer commands.
* neighbor PEER version VERSION:         BGP Peer commands.
* neighbor PEER weight WEIGHT:           BGP Peer commands.
* neighbor WORD peer-group:              BGP Peer Group.
* network A.B.C.D/M:                     BGP route.
* network A.B.C.D/M area <0-4294967295>: OSPF router.
* network A.B.C.D/M area A.B.C.D:        OSPF router.
* network IFNAME <1>:                    RIP Configuration.
* network IFNAME:                        ripngd Configuration.
* network NETWORK <1>:                   ripngd Configuration.
* network NETWORK:                       RIP Configuration.
* no aggregate-address A.B.C.D/M:        Route Aggregation.
* no area <0-4294967295> authentication: OSPF area.
* no area <0-4294967295> export-list NAME: OSPF area.
* no area <0-4294967295> import-list NAME: OSPF area.
* no area <0-4294967295> range A.B.C.D/M: OSPF area.
* no area <0-4294967295> shortcut:       OSPF area.
* no area <0-4294967295> stub:           OSPF area.
* no area <0-4294967295> stub no-summary: OSPF area.
* no area <0-4294967295> virtual-link A.B.C.D: OSPF area.
* no area A.B.C.D authentication:        OSPF area.
* no area A.B.C.D default-cost <0-16777215>: OSPF area.
* no area A.B.C.D export-list NAME:      OSPF area.
* no area A.B.C.D import-list NAME:      OSPF area.
* no area A.B.C.D range A.B.C.D/M:       OSPF area.
* no area A.B.C.D range IPV4_PREFIX substitute IPV4_PREFIX: OSPF area.
* no area A.B.C.D range IPV4_PREFIX suppress: OSPF area.
* no area A.B.C.D shortcut:              OSPF area.
* no area A.B.C.D stub:                  OSPF area.
* no area A.B.C.D stub no-summary:       OSPF area.
* no area A.B.C.D virtual-link A.B.C.D:  OSPF area.
* no auto-cost refrence-bandwidth:       OSPF router.
* no bandwidth <1-10000000>:             Interface Commands.
* no banner motd:                        Basic Config Commands.
* no bgp multiple-instance:              Multiple instance.
* no debug event:                        More Show IP BGP.
* no debug keepalive:                    More Show IP BGP.
* no debug ospf ism:                     Debugging OSPF.
* no debug ospf ism (status|events|timers): Debugging OSPF.
* no debug ospf lsa:                     Debugging OSPF.
* no debug ospf lsa (generate|flooding|refresh): Debugging OSPF.
* no debug ospf nsm:                     Debugging OSPF.
* no debug ospf nsm (status|events|timers): Debugging OSPF.
* no debug ospf packet (hello|dd|ls-request|ls-update|ls-ack|all) (send|recv) [detail]: Debugging OSPF.
* no debug ospf zebra:                   Debugging OSPF.
* no debug ospf zebra (interface|redistribute): Debugging OSPF.
* no debug update:                       More Show IP BGP.
* no default-information originate:      Redistribute routes to OSPF.
* no default-metric:                     Redistribute routes to OSPF.
* no default-metric <1-16>:              RIP Metric Manipulation.
* no distance <1-255> <1>:               RIP distance.
* no distance <1-255>:                   Redistribute routes to OSPF.
* no distance <1-255> A.B.C.D/M:         RIP distance.
* no distance <1-255> A.B.C.D/M ACCESS-LIST: RIP distance.
* no distance ospf:                      Redistribute routes to OSPF.
* no distribute-list NAME out (kernel|connected|static|rip|ospf: Redistribute routes to OSPF.
* no exec-timeout:                       Basic Config Commands.
* no ip as-path access-list WORD:        AS Path Access List.
* no ip as-path access-list WORD {permit|deny} LINE: AS Path Access List.
* no ip community-list expanded NAME:    BGP Community Lists.
* no ip community-list NAME:             BGP Community Lists.
* no ip community-list standard NAME:    BGP Community Lists.
* no ip extcommunity-list expanded NAME: BGP Extended Community Lists.
* no ip extcommunity-list NAME:          BGP Extended Community Lists.
* no ip extcommunity-list standard NAME: BGP Extended Community Lists.
* no ip ospf authentication-key:         OSPF interface.
* no ip ospf cost:                       OSPF interface.
* no ip ospf dead-interval:              OSPF interface.
* no ip ospf hello-interval:             OSPF interface.
* no ip ospf message-digest-key:         OSPF interface.
* no ip ospf network:                    OSPF interface.
* no ip ospf priority:                   OSPF interface.
* no ip ospf retransmit interval:        OSPF interface.
* no ip ospf transmit-delay:             OSPF interface.
* no ip prefix-list NAME:                IP Prefix List.
* no ip prefix-list NAME description [DESC]: ip prefix-list description.
* no ip prefix-list sequence-number:     ip prefix-list sequential number control.
* no ip rip authentication key-chain KEY-CHAIN: RIP Authentication.
* no ip rip authentication mode md5:     RIP Authentication.
* no ip rip authentication mode text:    RIP Authentication.
* no ip rip authentication string STRING: RIP Authentication.
* no ip split-horizon:                   RIP Configuration.
* no log stdout:                         Basic Config Commands.
* no log syslog:                         Basic Config Commands.
* no multicast:                          Interface Commands.
* no neighbor A.B.C.D:                   RIP Configuration.
* no neighbor PEER default-originate:    BGP Peer commands.
* no neighbor PEER description ...:      BGP Peer commands.
* no neighbor PEER dont-capability-negotiate: Capability Negotiation.
* no neighbor PEER ebgp-multihop:        BGP Peer commands.
* no neighbor PEER interface IFNAME:     BGP Peer commands.
* no neighbor PEER maximum-prefix NUMBER: BGP Peer commands.
* no neighbor PEER next-hop-self:        BGP Peer commands.
* no neighbor PEER override-capability:  Capability Negotiation.
* no neighbor PEER route-reflector-client: Route Reflector.
* no neighbor PEER shutdown:             BGP Peer commands.
* no neighbor PEER strict-capability-match: Capability Negotiation.
* no neighbor PEER update-source:        BGP Peer commands.
* no neighbor PEER weight WEIGHT:        BGP Peer commands.
* no network A.B.C.D/M:                  BGP route.
* no network A.B.C.D/M area <0-4294967295>: OSPF router.
* no network A.B.C.D/M area A.B.C.D:     OSPF router.
* no network IFNAME:                     RIP Configuration.
* no network NETWORK:                    RIP Configuration.
* no ospf abr-type TYPE:                 OSPF router.
* no ospf rfc1583compatibility:          OSPF router.
* no ospf router-id:                     OSPF router.
* no passive interface INTERFACE:        OSPF router.
* no passive-interface IFNAME:           RIP Configuration.
* no redistribute (kernel|connected|static|rip|bgp): Redistribute routes to OSPF.
* no redistribute bgp:                   How to Announce RIP route.
* no redistribute connected:             How to Announce RIP route.
* no redistribute kernel:                How to Announce RIP route.
* no redistribute ospf:                  How to Announce RIP route.
* no redistribute static:                How to Announce RIP route.
* no rouer rip:                          RIP Configuration.
* no route A.B.C.D/M:                    How to Announce RIP route.
* no router bgp ASN:                     BGP router.
* no router ospf:                        OSPF router.
* no router zebra:                       Redistribute routes to OSPF.
* no shutdown:                           Interface Commands.
* no smux peer OID:                      SMUX configuration.
* no smux peer OID PASSWORD:             SMUX configuration.
* no timers basic:                       RIP Timers.
* no timers spf:                         OSPF router.
* offset-list ACCESS-LIST (in|out):      RIP Metric Manipulation.
* offset-list ACCESS-LIST (in|out) IFNAME: RIP Metric Manipulation.
* ospf abr-type TYPE:                    OSPF router.
* ospf rfc1583compatibility:             OSPF router.
* ospf router-id A.B.C.D:                OSPF router.
* passive interface INTERFACE:           OSPF router.
* passive-interface IFNAME:              RIP Configuration.
* password PASSWORD:                     Basic Config Commands.
* redistribute (kernel|connected|static|rip|bgp): Redistribute routes to OSPF.
* redistribute (kernel|connected|static|rip|bgp) metric <0-16777214>: Redistribute routes to OSPF.
* redistribute (kernel|connected|static|rip|bgp) metric <0-16777214> route-map WORD: Redistribute routes to OSPF.
* redistribute (kernel|connected|static|rip|bgp) metric-type (1|2): Redistribute routes to OSPF.
* redistribute (kernel|connected|static|rip|bgp) metric-type (1|2) metric <0-16777214>: Redistribute routes to OSPF.
* redistribute (kernel|connected|static|rip|bgp) metric-type (1|2) metric <0-16777214> route-map WORD: Redistribute routes to OSPF.
* redistribute (kernel|connected|static|rip|bgp) metric-type (1|2) route-map WORD: Redistribute routes to OSPF.
* redistribute (kernel|connected|static|rip|bgp) ROUTE-MAP: Redistribute routes to OSPF.
* redistribute bgp:                      How to Announce RIP route.
* redistribute bgp metric <0-16>:        How to Announce RIP route.
* redistribute bgp route-map ROUTE-MAP:  How to Announce RIP route.
* redistribute connected <1>:            How to Announce RIP route.
* redistribute connected <2>:            Redistribute to BGP.
* redistribute connected:                Redistribute routes to OSPF6.
* redistribute connected metric <0-16>:  How to Announce RIP route.
* redistribute connected route-map ROUTE-MAP: How to Announce RIP route.
* redistribute kernel <1>:               How to Announce RIP route.
* redistribute kernel:                   Redistribute to BGP.
* redistribute kernel metric <0-16>:     How to Announce RIP route.
* redistribute kernel route-map ROUTE-MAP: How to Announce RIP route.
* redistribute ospf <1>:                 How to Announce RIP route.
* redistribute ospf:                     Redistribute to BGP.
* redistribute ospf metric <0-16>:       How to Announce RIP route.
* redistribute ospf route-map ROUTE-MAP: How to Announce RIP route.
* redistribute rip:                      Redistribute to BGP.
* redistribute ripng:                    Redistribute routes to OSPF6.
* redistribute static <1>:               How to Announce RIP route.
* redistribute static <2>:               Redistribute routes to OSPF6.
* redistribute static:                   Redistribute to BGP.
* redistribute static metric <0-16>:     How to Announce RIP route.
* redistribute static route-map ROUTE-MAP: How to Announce RIP route.
* refresh age-diff <0-10000>:            OSPF router.
* refresh group-limit <0-10000>:         OSPF router.
* refresh per-slice <0-10000>:           OSPF router.
* route A.B.C.D/M:                       How to Announce RIP route.
* route NETWORK:                         ripngd Configuration.
* route-map ROUTE-MAP-NAME permit PRIORITY: Route Map Command.
* router bgp AS-NUMBER:                  BGP instance and view.
* router bgp AS-NUMBER view NAME:        BGP instance and view.
* router bgp ASN:                        BGP router.
* router ospf:                           OSPF router.
* router ospf6:                          OSPF6 router.
* router rip:                            RIP Configuration.
* router ripng:                          ripngd Configuration.
* router zebra <1>:                      Redistribute routes to OSPF.
* router zebra:                          ripngd Configuration.
* router-id A.B.C.D:                     OSPF6 router.
* service advanced-vty:                  Basic Config Commands.
* service password-encryption:           Basic Config Commands.
* service terminal-length <0-512>:       Basic Config Commands.
* set as-path prepend AS-PATH:           Using AS Path in Route Map.
* set as-path prepend AS_PATH:           Route Map Set Command.
* set comm-list WORD delete:             BGP Community in Route Map.
* set community COMMUNITY <1>:           BGP Community in Route Map.
* set community COMMUNITY:               Route Map Set Command.
* set community COMMUNITY additive:      BGP Community in Route Map.
* set community none:                    BGP Community in Route Map.
* set extcommunity rt EXTCOMMUNITY:      BGP Extended Communities in Route Map.
* set extcommunity soo EXTCOMMUNITY:     BGP Extended Communities in Route Map.
* set ip next-hop A.B.C.D:               RIP route-map.
* set ip next-hop IPV4_ADDRESS:          Route Map Set Command.
* set ipv6 next-hop global IPV6_ADDRESS: Route Map Set Command.
* set ipv6 next-hop local IPV6_ADDRESS:  Route Map Set Command.
* set local-preference LOCAL_PREF:       Route Map Set Command.
* set metric <0-4294967295>:             RIP route-map.
* set metric METRIC:                     Route Map Set Command.
* set weight WEIGHT:                     Route Map Set Command.
* show debug:                            More Show IP BGP.
* show debugging ospf:                   Debugging OSPF.
* show debugging rip:                    RIP Debug Commands.
* show debugging ripng:                  ripngd Terminal Mode Commands.
* show interface:                        zebra Terminal Mode Commands.
* show ip bgp:                           Show IP BGP.
* show ip bgp A.B.C.D:                   Show IP BGP.
* show ip bgp community COMMUNITY <1>:   Display BGP Routes by Community.
* show ip bgp community COMMUNITY:       More Show IP BGP.
* show ip bgp community COMMUNITY exact-match <1>: More Show IP BGP.
* show ip bgp community COMMUNITY exact-match: Display BGP Routes by Community.
* show ip bgp community-list WORD <1>:   Display BGP Routes by Community.
* show ip bgp community-list WORD:       More Show IP BGP.
* show ip bgp community-list WORD exact-match <1>: More Show IP BGP.
* show ip bgp community-list WORD exact-match: Display BGP Routes by Community.
* show ip bgp neighbor [PEER]:           More Show IP BGP.
* show ip bgp regexp LINE <1>:           More Show IP BGP.
* show ip bgp regexp LINE:               Display BGP Routes by AS Path.
* show ip bgp summary:                   More Show IP BGP.
* show ip bgp view NAME:                 Viewing the view.
* show ip bgp X:X::X:X:                  Show IP BGP.
* show ip community-list:                BGP Community Lists.
* show ip community-list NAME:           BGP Community Lists.
* show ip extcommunity-list:             BGP Extended Community Lists.
* show ip extcommunity-list NAME:        BGP Extended Community Lists.
* show ip ospf:                          Showing OSPF information.
* show ip ospf database:                 Showing OSPF information.
* show ip ospf database (asbr-summary|external|network|router|summary): Showing OSPF information.
* show ip ospf database (asbr-summary|external|network|router|summary) adv-router ADV-ROUTER: Showing OSPF information.
* show ip ospf database (asbr-summary|external|network|router|summary) LINK-STATE-ID: Showing OSPF information.
* show ip ospf database (asbr-summary|external|network|router|summary) LINK-STATE-ID adv-router ADV-ROUTER: Showing OSPF information.
* show ip ospf database (asbr-summary|external|network|router|summary) LINK-STATE-ID self-originate: Showing OSPF information.
* show ip ospf database (asbr-summary|external|network|router|summary) self-originate: Showing OSPF information.
* show ip ospf database max-age:         Showing OSPF information.
* show ip ospf database self-originate:  Showing OSPF information.
* show ip ospf interface [INTERFACE]:    Showing OSPF information.
* show ip ospf neighbor:                 Showing OSPF information.
* show ip ospf neighbor detail:          Showing OSPF information.
* show ip ospf neighbor INTERFACE:       Showing OSPF information.
* show ip ospf neighbor INTERFACE detail: Showing OSPF information.
* show ip ospf refresher:                Showing OSPF information.
* show ip ospf route:                    Showing OSPF information.
* show ip prefix-list:                   Showing ip prefix-list.
* show ip prefix-list detail:            Showing ip prefix-list.
* show ip prefix-list detail NAME:       Showing ip prefix-list.
* show ip prefix-list NAME:              Showing ip prefix-list.
* show ip prefix-list NAME A.B.C.D/M:    Showing ip prefix-list.
* show ip prefix-list NAME A.B.C.D/M first-match: Showing ip prefix-list.
* show ip prefix-list NAME A.B.C.D/M longer: Showing ip prefix-list.
* show ip prefix-list NAME seq NUM:      Showing ip prefix-list.
* show ip prefix-list summary:           Showing ip prefix-list.
* show ip prefix-list summary NAME:      Showing ip prefix-list.
* show ip protocols:                     Show RIP Information.
* show ip rip:                           Show RIP Information.
* show ip ripng:                         ripngd Terminal Mode Commands.
* show ip route:                         zebra Terminal Mode Commands.
* show ipforward:                        zebra Terminal Mode Commands.
* show ipv6 ospf6 [INSTANCE_ID]:         Showing OSPF6 information.
* show ipv6 ospf6 database:              Showing OSPF6 information.
* show ipv6 ospf6 interface:             Showing OSPF6 information.
* show ipv6 ospf6 neighbor:              Showing OSPF6 information.
* show ipv6 ospf6 request-list A.B.C.D:  Showing OSPF6 information.
* show ipv6 route:                       zebra Terminal Mode Commands.
* show ipv6 route ospf6:                 Showing OSPF6 information.
* show ipv6forward:                      zebra Terminal Mode Commands.
* show version:                          Basic Config Commands.
* shutdown:                              Interface Commands.
* smux peer OID:                         SMUX configuration.
* smux peer OID PASSWORD:                SMUX configuration.
* table TABLENO:                         Static Route Commands.
* terminal length <0-512>:               Basic Config Commands.
* timers basic UPDATE TIMEOUT GARBAGE:   RIP Timers.
* timers spf <0-4294967295> <0-4294967295>: OSPF router.
* version VERSION:                       RIP Configuration.
* who:                                   Basic Config Commands.
* write file:                            Basic Config Commands.
* write terminal:                        Basic Config Commands.


File: zebra.info,  Node: VTY Key Index,  Prev: Command Index,  Up: Top

VTY Key Index
*************

* Menu:

* <DEL>:                                 CLI Editing Commands.
* <DOWN>:                                CLI Advanced Commands.
* <LEFT>:                                CLI Movement Commands.
* <RIGHT>:                               CLI Movement Commands.
* <TAB>:                                 CLI Advanced Commands.
* <UP>:                                  CLI Advanced Commands.
* ?:                                     CLI Advanced Commands.
* C-a:                                   CLI Movement Commands.
* C-b:                                   CLI Movement Commands.
* C-c:                                   CLI Advanced Commands.
* C-d:                                   CLI Editing Commands.
* C-e:                                   CLI Movement Commands.
* C-f:                                   CLI Movement Commands.
* C-h:                                   CLI Editing Commands.
* C-k:                                   CLI Editing Commands.
* C-n:                                   CLI Advanced Commands.
* C-p:                                   CLI Advanced Commands.
* C-t:                                   CLI Editing Commands.
* C-u:                                   CLI Editing Commands.
* C-w:                                   CLI Editing Commands.
* C-z:                                   CLI Advanced Commands.
* M-b:                                   CLI Movement Commands.
* M-d:                                   CLI Editing Commands.
* M-f:                                   CLI Movement Commands.



Tag Table:
Node: Top1115
Node: Overview1639
Node: About Zebra3056
Node: System Architecture5325
Node: Supported Platforms8323
Node: Supported RFC9310
Node: How to get Zebra11112
Node: Mailing List11817
Node: Bug Reports12484
Node: Installation13329
Node: Configure the Software13760
Ref: Configure the Software-Footnote-116127
Node: Build the Software17769
Node: Install the Software18311
Node: Basic commands19682
Node: Config Commands20395
Node: Basic Config Commands21277
Node: Sample Config File23675
Node: Common Invocation Options24435
Node: Virtual Terminal Interfaces25557
Node: VTY Overview26062
Node: VTY Modes27345
Node: VTY View Mode27785
Node: VTY Enable Mode28039
Node: VTY Other Modes28303
Node: VTY CLI Commands28465
Node: CLI Movement Commands28915
Node: CLI Editing Commands29448
Node: CLI Advanced Commands30021
Node: Zebra30772
Node: Invoking zebra31279
Node: Interface Commands31865
Node: Static Route Commands32695
Node: zebra Terminal Mode Commands34782
Node: RIP35743
Node: Starting and Stopping ripd36678
Node: RIP netmask38099
Node: RIP Configuration39221
Node: How to Announce RIP route43116
Node: Filtering RIP Routes45645
Node: RIP Metric Manipulation47104
Node: RIP distance48007
Node: RIP route-map48810
Node: RIP Authentication51312
Node: RIP Timers52402
Node: Show RIP Information53677
Node: RIP Debug Commands55040
Node: RIPng56024
Node: Invoking ripngd56342
Node: ripngd Configuration56599
Node: ripngd Terminal Mode Commands57338
Node: ripngd Filtering Commands57688
Node: OSPFv258187
Node: Configuring ospfd58744
Node: OSPF router59221
Node: OSPF area60952
Node: OSPF interface63166
Node: Redistribute routes to OSPF65948
Node: Showing OSPF information68064
Node: Debugging OSPF69284
Node: OSPFv370295
Node: OSPF6 router70613
Node: OSPF6 area70970
Node: OSPF6 interface71142
Node: Redistribute routes to OSPF671994
Node: Showing OSPF6 information72298
Node: BGP73103
Node: Starting BGP73964
Node: BGP router74549
Node: BGP distance75785
Node: BGP decision process76226
Node: BGP network76482
Node: BGP route76663
Node: Route Aggregation77224
Node: Redistribute to BGP77776
Node: BGP Peer78285
Node: Defining Peer78463
Node: BGP Peer commands79079
Node: Peer filtering81450
Node: BGP Peer Group81941
Node: BGP Address Family82243
Node: Autonomous System82388
Node: AS Path Regular Expression83264
Node: Display BGP Routes by AS Path84375
Node: AS Path Access List84804
Node: Using AS Path in Route Map85258
Node: Private AS Numbers85524
Node: BGP Communities Attribute85669
Node: BGP Community Lists88130
Node: Numbered BGP Community Lists90807
Node: BGP Community in Route Map92382
Node: Display BGP Routes by Community94309
Node: Using BGP Communities Attribute95325
Node: BGP Extended Communities Attribute98883
Node: BGP Extended Community Lists100673
Node: BGP Extended Communities in Route Map102574
Node: Displaying BGP routes103017
Node: Show IP BGP103243
Node: More Show IP BGP103965
Node: Capability Negotiation105085
Node: Route Reflector108373
Node: Route Server108638
Node: Multiple instance109696
Node: BGP instance and view111509
Node: Routing policy112875
Node: Viewing the view113631
Node: How to set up a 6-Bone connection113903
Node: Dump BGP packets and table115275
Node: VTY shell115805
Node: Filtering116645
Node: IP Access List116993
Node: IP Prefix List117384
Node: ip prefix-list description120553
Node: ip prefix-list sequential number control121086
Node: Showing ip prefix-list121611
Node: Clear counter of ip prefix-list122694
Node: Route Map123115
Node: Route Map Command123616
Node: Route Map Match Command123819
Node: Route Map Set Command124427
Node: IPv6 Support125285
Node: Router Advertisement125850
Node: Kernel Interface126181
Node: SNMP Support128131
Node: How to get ucd-snmp128760
Node: SMUX configuration129808
Node: Zebra Protocol130241
Node: Packet Binary Dump Format132135
Node: Command Index143702
Node: VTY Key Index173346

End Tag Table
